Hi-Force TWE Series Скачать руководство пользователя страница 11

 

OPERATING INSTRUCTIONS: 

Electric Torque Wrench 

Series: TWE 

TDS:- 

1399 

Prepared by:-  M.DAVIES 

Approved by:- 

 

Date: 25/03/14 

REV NO:- 

 

 

 

 

ECO:-  

 

 

 

 

 

 

Page 

11

 of 

20

 

 

3.1.8

 

Restart protection 

With the gear and motor rotating, it is 
not possible to engage the right/left 
switch. This also applies for the on/off 
switch. After the gear and motor have 
stopped rotating for 2-3 seconds, the 
machine can be restarted. 
The respective direction LED will flash 
blue. 
 

 

3.2. TORQUE ANGLE MODE (OPTIONAL) 

Push the button <Select> to switch 
between the modes FAST 

u

STRONG and angle of tilt mode M+α. 
Releasing the button <Select> causes 
the respective selection, including the 
symbol, to flash three times. Then the 
selected mode is engaged. 
 

 

ATTENTION: 
Angle of tilt mode selection is only 
possible in gear 1 mode. If this 
selection is attempted in gear 2 mode, a 
warning signal sounds. The “2” in the 
display and the two directional LEDs 
will flash red alternately. 
 

 

In angle of tilt mode, the last setting of 
snugging torque alternates every 2 
seconds (≡)… 

 

…with the last setting for the continued 
turning angle (°). 

 

The setting visible at any time can be 
changed by turning the potentiometer 
wheel (2). Once the potentiometer 
wheel stops, the set value flashes in the 
display, as does the <Enter> button, 
until the value is confirmed by pressing 
<Enter>. Should the enter button not be 
pressed within 3 seconds, the value is 
not engaged and the original set value 
will appear in the display. 

 

 

Содержание TWE Series





















Отзывы: