HF PackerAmp V4 Скачать руководство пользователя страница 2

Страница: 2 / 76

Contents

Circuit Details ...................................................................... 5

Performance ........................................................................ 6

Terms used in the descriptions ............................................ 6

Preparation .......................................................................... 7

Construction Techniques ..................................................... 7

Good Soldering Technique .................................................. 7

Suggested Tools ................................................................. 8

Included Speciality Tools ..................................................... 8

Component Installation ........................................................ 8

Care of the IRF-510 MOSFET's ........................................... 9

Other Construction Notes .................................................... 9

Section Two – Amplifier Module Construction ....................... 10

Assembly Steps ................................................................. 10

Spacer Assembly .............................................................. 12

Fabrication and Assembly of T2 ........................................ 13

Fabrication and Assembly of T3 ........................................ 14

Fabrication and Assembly of L1 and L3 ............................. 14

Fabrication and Assembly of L2......................................... 15

Assembly of RFM2 ............................................................ 15

Clean and Inspect the Board ............................................. 16

Section 3 - Low Pass Filter Module Assembly ...................... 17

Organize for Assembly ...................................................... 17

Install Relays and Diodes ................................................. 17

Capacitor Assembly .......................................................... 17

Core Winding Table .......................................................... 18

Core Winding Technique .................................................. 18

Core Installation ................................................................ 19

Switch Assembly ............................................................... 19

Connector Assembly ......................................................... 19

In-Circuit Tuning Adjustments ........................................... 20

......................................................................................... 20

Selector Switch Stop Pins Installation ............................... 20

......................................................................................... 20

Amplifier Cable Connections

Error! Bookmark not defined.

Section 4 – Case and Chassis Assemblies ........................... 23

Case Preparation .............................................................. 23

Heat Sink Assembly .......................................................... 23

RF Input Cable .................................................................. 23

RF Output Cable ............................................................... 24

Low Pass Filter Input Cable Fabrication ............................ 25

Low Pass Filter Output Cable Fabrication ......................... 26

On/Bypass Switch and LED Wiring ................................... 27

Power Pole Physical Installation ....................................... 28

Power Wiring Connections ................................................ 29

Install Rear Panel Power Switch ....................................... 29

Install Wiring for Power ..................................................... 29

Содержание PackerAmp V4













































































Результаты поиска

Содержание PackerAmp V4

Отзывы:

Похожие инструкции для PackerAmp V4

Бренды по названию

Популярные бренды

HF PackerAmp V4, Руководство по монтажу

Результаты поиска

Содержание PackerAmp V4

Отзывы:

Похожие инструкции для PackerAmp V4

Бренды по названию

Популярные бренды