background image

TW-810T 

■FCC/IC Warning 

Information about FCC Standard. 

Contains FCC ID: T82-HRF2403 

 

This device complies with part 15 of the FCC Rules. 

Operation is subject to the following two conditions: 

(1) This device may not cause harmful interference, and 

(2) this device must accept any interference received, including interference that may cause undesired 

operation. 

 

FCC CAUTION 
Changes or modifications not expressly approved by the party responsible for compliance could void the 
user’s authority to operate the equipment. 

 

This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. 

 

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment 

and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment has very low levels of 

RF energy that is deemed to comply without maximum permissive exposure evaluation (MPE). 

 

This equipment complies with FCC radiation exposure limits set forth for an  uncontrolled environment 

and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment has very low levels of 

RF energy that is deemed to comply without testing of specific absorption rate(SAR). 

 

 

Содержание TW-810T

























Отзывы: