manualshive.com logo in svg

Heraeus CRYOFUGE 6000i, Руководство по эксплуатации

Поделиться
Скачать
Heraeus CRYOFUGE 6000i Скачать руководство пользователя страница 21

Transport and Installation

17

Installation place

The rear side of the CRYOFUGE must be positioned at least 50 cm away from the wall and at least 30 cm
away from the side. Therefore, a level, secure surface of at least 1.5 m² is required.

CAUTION!
The centrifuge must not be placed near to heat generators or radiators!

The surface load of 1300 N/m² requires a secure surface (concrete) and if necessary, a foundation.

WARNING!
The safety regulations require the marking of a danger area of 30 cm around the appliance, with the
notice that during centrifuging, neither persons nor hazardous materials may be inside this area.

Connection requirements

Before the centrifuge is connected to the power supply, it must be ensured that:

1.

The voltage specifications on the type plate are identical to the available supply voltage:
400 V / 50 Hz (3  neutral con earthed conductor)

2.

The neutral conductor can be applied with 25 A (unsymmetrical phase loading)

3.

For the connection a CEKON socket (32A-6h, 3L+N+PE) and for permanent connection, a three-pole
isolating switch (3 x 63 A) is available.

CAUTION!
A permanent installation of the electrical wiring must only be carried out by a qualified electrician!

Start-up

Connect the plug to the required CEKON socket (32 A), or remove the plug and permanently install the
cable.

Switch on the power switch on the front right.

All 7-segment displays and diodes light up for a short time to be tested (system check).

CAUTION!
The power switch must not be used to stop the centrifuge procedure (apart from in cases of emer-
gency). To stop the centrifuge, use the QUICK STOP or STOP key!

Opening the lid

The centrifuge lid can only be opened when the yellow LED is lit up. This is only possible when the rotor is
not rotating or has finished rotating and no error messages are shown.

CAUTION – DANGER!
The mechanical lid unlocking system, (emergency lid opening) must only be used in cases of
emergency, e.g. if there is an interruption in the electricity supply.
You must wait until the drive has come to a complete stop!
(See instructions for safety equipment, page 6)

Содержание CRYOFUGE 6000i























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды