Henny Penny SmartCombi ESC-220 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 44

background image

Smart

Combi™

Service

generic gas fault

all gas units

Description:

This error message appears if F1 has changed to F0 (flame detection from the electronic) 5 times
during a cooked process, without demand from the software temperature controller (i.e. during the heat
demand). In this case the igniting box has independently ignited a lapsed flame again. This is not
normal and the possibility passes that the gas burner or other gas/air components are blocked. A high
CO eduction is possible. If the "flame OK signal (F0)" would never recognized, this error is
suppressed. There can be an electrical problem if there is no blockage of the gas pipe. This means that
the“ flame OK“ signal conducted reliably to the control. The reason could be the ignition box, the
flame-signal board into the harness or wrong wiring at the ignition box

Troubleshooting:

Remedy

Function o.k. ?

Yes

No

Check ignition box N10 / N20 (N20 only at HD20.x).

Check ionisation electrode

Change flame-signal board located at the harness (N11 / N22 (N22
only at HD20.x)

The unit does not heating (no error message)

Description:

There is no demand on the ignition box.

Troubleshooting:

Remedy

Function o.k. ?

Yes

No

Check fuse F4 at the relay card A1.

34

«
...
32
33
34
35
36
...
»

Содержание SmartCombi ESC-220













































Отзывы:

Нет отзывов

Похожие инструкции для SmartCombi ESC-220

Бренд: wad Страницы: 33

CV4000 vaporino

Бренд: UFESA Страницы: 56

CLATRONIC NBE 2795

Бренд: CTC Union Страницы: 50

Бренд: Cleveland Страницы: 27

Бренд: TEFAL Страницы: 18

Бренд: Braun Страницы: 73

Бренд: V-ZUG Страницы: 88

Бренд: KALOS Страницы: 10

Бренд: Hitachi Страницы: 29

Бренд: Hitachi Страницы: 40

Бренд: Hitachi Страницы: 9

Бренд: KING Страницы: 12

Oral-B PRO-HEALTH JR

Бренд: Braun Страницы: 16

Бренд: Trotec Страницы: 10

Бренд: Olimpia splendid Страницы: 84

Бренд: Dyna-Glo Страницы: 24

Бренд: Vornado Страницы: 13

Бренд: Tesco Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды