background image

Model K-450 Wiring Diagrams 

120 Volts / 1000 Watts 

15 AMP/ 125-Volt Grounding Plug 

NEMA 5-15P Provided 

CHANGING THE THERMOSTAT 

 

1.

 

Disconnect from the power source. 

2.

 

Remove rods from oven. 

3.

 

Remove element cover and pull temperature-sensing 
tube from holder. 

4.

 

Loosen setscrew in thermostat knob and remove knob. 
Remove chrome mounting ring (bezel). 

5.

 

Remove nine (9) mounting screws from leg assembly 
and lift oven clear of leg 

6.

 

Remove electrical leads from thermostat and remove 
thermostat by pulling sensing tube through conduit. 

7.

 

To replace new thermostat, pass sensing tube through 
conduit, being sure there is adequate length to reach the 
holder. 

8.

 

Reconnect electrical leads to new thermostat and mount 
thermostat to chrome ring (bezel) loosely with red indicting 
line in upward position. Place knob on thermostat stem and 
check rotation of knob. When knob turns freely, remove and 
tighten chrome mounting ring (bezel) 

240 Volts / 1000 Watts 

Grounding Plug 

NEMA 5-15P 

9.

 

Replace leg assembly being sure wiring is not 
crimped between oven wall and leg. 

 

10.

 

Replace thermostat knob. 

11.

 

Insert temperature-sensing tube into holder and 
replace element cover. 

  

 

THERMOSTAT CALIBRATION 

 

1.

 

Turn on unit. Set control dial at desired 
temperature. 

2.

 

Allow control to cycle at least three times and 
observe temperature at middle of fourth cycle. 

3.

 

If calibration is required, carefully remove dial 
knob. Do not turn shaft. 

480 Volts / 1000 Watts 

20 AMP/ 480-Volt  

Grounding Plug NEMA 8-20P Not  Provided 

4.

 

Turn calibration screw in center of dial shaft. 
(Turning set screw clockwise decreases temperature. 
Turning setscrew counter-clockwise increases 
temperature. One-fourth [1/4] turn equals 
approximately 35ºF.) 

5.

 

Allow unit to cycle at least three times and 
observe temperature at middle of fourth 
cycle. Readjust calibration screw if 
necessary. Replace dial knob

 

Содержание K-450









Отзывы: