background image

Scheduled Maintenance 

 

The manufacturer recommends that the unit be unloaded and cleaned of debris and dust 

every six months. It is recommended that a temperature probe be placed inside the unit and the 
thermostat calibration checked at this time. 

 

Venting 

 

Your model K-450 oven is vented through a screened plug at the rear of the oven. 

 

Troubleshooting 

 

The Keen oven model K-450 requires a minimal amount 

 of electrical knowledge to repair if necessary. 

 
 

IF OVEN FAILS TO OPERATE – NO HEAT 

 

1.

 

Check power source. 

2.

 

Check power cord continuity. Replace cord assembly if faulty. 

3.

 

If pilot light glows, voltage is being supplied to he heating element. Check element 
continuity. If defective, replace. 

4.

 

If thermostat cannot be heard clicking on and off when dial is rotated, and if pilot light fails 
to operate, replace thermostat

 

 

 

IF OVEN OVERHEATS 

 
1.

 

If oven fails to cycle on and off and reaches a temperature above 550ºF, thermostat is faulty 
and needs replacing. 

2.

 

If oven operates but is off from setting see calibration instructions. 

 

 

Corrective Maintenance 

 

CHANGING THE HEATING ELEMENT 

 

1.

 

Disconnect power source and remove any rods from oven. 

2.

 

Remove element cover. 

3.

 

Remove element mounting nuts and top ceramic insulators. 

4.

 

Remove nine (9) mounting screws from leg assembly and lift oven clear of leg. 

5.

 

Remove wire connectors from element leads. 

6.

 

Remove old element from oven by lifting element over mounting bolts and pulling element 
leads through conduit. Remove bottom ceramic insulators. 

7.

 

Install new male ceramic insulators, element, female insulators and hex nuts. 

8.

 

Insert element leads through conduit and reconnect with original electrical leads. 

9.

 

Replace front leg assembly being sure wiring is not crimped between leg and oven wall.

 

Содержание K-450









Отзывы: