manualshive.com logo in svg

Helo HSX M 120, Инструкции по эксплуатации и монтажу

Поделиться
Скачать
Helo HSX M 120 Скачать руководство пользователя страница 11

 

 

 

11

 
Control panel function: 

 
The steam generator is turned on by pressing the ON-OFF button on the control panel. After this, 
the temperature display will begin to flash. The temperature can be set to the degree (ranging 
between 25 °C – 50 °C) by pressing the + or – buttons. If the temperature value on the display is 
correct, press the OK button and move on to the time display. While the display is flashing, you can 
set the time to the minute (up to 90 minutes) using the + or – buttons, after which the display will 
change to hours (max. 4 hours). 
When the time remaining reaches 90 minutes, the display will change back to minutes. Any time 
beyond 90 minutes is only displayed in full hours. 
 

Light control: 

 
Lights can be controlled by a control panel button, which, when pressed, will activate an LED next 
to the button. 
Connectors LC1 and LC2 on the circuit board are for light control. The circuit board draws external 
voltage (24V DC max. 50mA), which is switched to connector LC1. When the light button is 
pressed, the circuit board transistor will transfer power to connector LC2, which controls the actual 
lighting unit. 
 
 
 

BUTTON HSX M 
 

 

 

Button function: 
 

Turning on the steam generator with the button will take 30 minutes, at which time the LED above 
the button will come on. The steam generator time cannot be set – it will shut itself off. The steam 
generator can also be shut off before time runs out by pressing the button, at which time the LED 
will turn off. If desired, the steam generator can be turned on again. 
. 
When using 

the push button

 it is recommended to install the limiting thermostat to prevent the rise 

of the temperature above +50 °C when the steam room is used for longer than 30 minutes, which is 
the fixed operating time of a steamer equipped with a push button. See the separate installation and 
connection picture. 
The 2-phase control works with the button control version by switching off two thermal resistors 
with a contactor when the thermostat measures a temperature of +50 °C. When the temperature 
drops 1 °C, all three resistors are switched back on. If the temperature rises above +50 °C, all three 
resistors will be switched off. 
 
 

ON - OFF button

Led indicator light

Содержание HSX M 120
















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды