Installation Instructions and Instructions for Use
Subject to technical modifications – Date of Issue May/2020
7
Connection diagram
ONYX.NODE
0
+
N
N
N
L
L
LOCAL
MOTOR
POWER
M
~
N
L
PE
1,5mm²
0,5mm²
0,75 - 1,5mm²
ONYX.NODE
0
+
N
N
N
L
L
LOCAL
MOTOR
POWER
1,5mm²
0,5mm²
0,75 - 1,5mm²
1
2
3
4
5
6
6
Fig. 2: Wiring diagram for Venetian blind, roller shutter and awning motor, lighting
Legend
1
Junction box
4
Motor
2
Button
5
Lighting
3
Switch (pushbutton possible)
6
ONYX.NODE
Installation Instructions and Instructions for Use
8
Subject to technical modifications – Date of Issue May/2020
Connection diagram
Attention!
The motor cable must be directly connected to the control device ON-
YX.NODE: Clamping points/junctions in the motor cable are unacceptable.
Attention!
When actuating the 230 V lighting, the maximum output power of 450 VA
may not be exceeded. This must especially be observed with lightings with
electrical ballasts, which have a high inrush current.
In addition, a cut-off relay must be used with higher electric capacities.
“Power”-terminals for mains voltage 230 V AC / 50 Hz
The input is provided for the voltage supply of the module and the load. The names L and
N mark live cord and neutral conductor. Both clamps (L and N) are present in duplicate, the
voltage supply can thus be transferred to the next control device. Observe the terminal
assignment in Fig.1.
"Motor"-terminals for motor connection
The outputs are provided for the connection of the drive or the connection of the lighting.
The arrows on the device show the running direction of the drive. 230 V lighting is con-
nected to N and
(L).
"Local"-terminals for pushbutton
To control the ONYX.NODE, a Venetian blind pushbutton or a switch / pushbutton for the
lighting can be connected to the terminals “Local”. Hence, the ONYX.NODE can also be
operated without a smart phone. Up to four ONYX.NODE (Art.-No. 50680002) can be
connected to a central pushbutton (a switch in case of lighting possible). If several ON-
YX.NODE are to be operated by one pushbutton, the following must be observed:
- All ONYX.NODE must be connected to the same phase.
- If several ONYX.NODE are operated by one pushbutton only, make sure that L and N
are not interchanged.
- The cabling may only be performed in a de-energized condition.
Installation Instructions and Instructions for Use
Subject to technical modifications – Date of Issue May/2020
9
Connection diagram
Direction assignment of the outputs when connecting a Venetian blind, roller shut-
ter, awning motor
After having connected the drive, please check the direction assignment of the outputs.
When pressing the pushbutton into the UP-direction, the motor must move into the retract-
ing direction. When pressing the pushbutton into the DOWN-direction, the motor must
move into the extending direction. If this is not the case, please exchange the connections
on the outputs. The direction assignment can take place through the ONYX
®
-app at a later
time.
Configuration
Before configuring the ONYX.NODE, download HELLA’s free app ONYX
®
from the app store / Google Play to your smart phone.
Before you can use ONYX.NODE in combination with ONYX.CENTER or
ONYX.CLICK, ONYX.NODE must be added in the app ONYX
®
. You will find
all information regarding the configuration in the instructions for ON-
YX.CENTER / ONYX.CLICK, directly in the app ONYX
®
or in the download
area on our homepage https://www.hella.info.
Precondition:
ONYX.NODE is installed (see chapter “Wiring diagram”). The mechanical
end positions of the drives must be adjusted.
Installation Instructions and Instructions for Use
10
Subject to technical modifications – Date of Issue May/2020
Operating guidelines
Roller shutter mode
If a pushbutton is pressed briefly, the drive moves to the respective end
position (latching mode). As a standard, the roller shutter mode is adjusted
on delivery.
Venetian blind mode
If the pushbutton is pressed briefly (<2 seconds), the drive stops after releas-
ing the pushbutton (tilting mode). If the pushbutton is pushed for more than
two seconds, the drive moves to the respective end position (latching mode).
Light mode
When pressing the pushbutton, the lighting is switched on. When pressing
the pushbutton again, the lighting is switched off. Only in the light mode, also
a switch can be connected to the control device.
Groups
Groups with their different sun protection units can be configured freely in the
ONYX
®
-app. All units in one group can be controlled together.
Favourite position (heart symbol)
In the ONYX
®
-app six freely selectable positions per sun protection unit can
be saved, which you simply can use again at a later time.
Automatic Operation
In the ONYX
®
-app you can set up as many time functions as you like, which,
at the desired times, make your sun protection units move to the adjusted
positions. ONYX
®
is also provided with an astro function, which, at sunrise or
sunset, moves your sun protection unit automatically to a defined position.
With the help of the sun sensor a particular position can be defined, if the
threshold value of the sun is below or exceeds the preset value.
