background image

- 3 -

1/ IMPORTANT SAFETY INFORMATION

IMPORTANT SAFETY PRECAUTIONS

1. Read the OWNER'S OPERATING MANUAL and all accompanying literature and follow it carefully

before using your machine.

2. Inspect your exercise machine prior to exercising to ensure that all nuts and bolts are fully tightened before

each use.

3. Most exercise equipment is not recommended for small children. Children should not use the machine

unless they are under adult supervision.

4. Exercise equipment has moving parts. In the interest of safety, keep others, especially children, at a safe

distance while exercising.

5. Warm up 5 to 10 minutes before each workout and cool down 5 to 10 minutes afterward. This allows your

heart rate to gradually increase and decrease and will help prevent straining muscles.

6. Never hold your breath while exercising. Breathing should remain at a normal rate in conjunction with the

level of exercise being performed.

7. Rest adequately between workouts. Muscles tone and develop during these rest periods. Beginners should

work out twice a week and increase gradually to 4 or 5 times per week.

8. Remove all jewelry, including rings, chains and pins before commencing exercise.
9. Always wear suitable clothing and footwear during exercise. Do not wear loose fitting clothing that could

become entangled with the moving parts of your exercise machine.

10. This machine is intended for household use only. It is not designed for commercial use.

IMPORTANT!!!  THE MAXIMUM RECOMMENDED WEIGHT CAPACITY FOR YOUR Helix is

130Kg (286 lbs.) per user.

WARNING:  Before commencing with any exercise program, please consult your family physician.

If at any time during exercise you feel faint, dizzy or experience pain, stop and consult your family

physician. In the event any of the above mentioned warnings are breached by the consumer, the

manufacturer may use same as a defense to any claim for injuries, damage or loss. The above warnings

are in no way intended to limit or modify the consumer's remedies for breach of warranties pursuant

to applicable Federal and State Laws of Regulations. They are being supplied strictly to ensure the

safety of the individuals using this product.

The Surgeon General

has determined that

lack of physical activity is 

detrimental to your health. 

!

THIS OWNER’S MANUAL CONTAINS ASSEMBLY, OPERATION, MAINTENANCE AND SAFETY
INFORMATION. IN THE INTEREST OF SAFETY, PLEASE MAKE CERTAIN THAT YOU READ AND
UNDERSTAND ALL THE INFORMATION BELOW.

helix manuals_Helix H1000 - hires  24/04/2014  18:39  Page 3

1  IMPORTANT SAFETY INFORMATION     

2

    Important Safety Precautions     

2

    Weight Limit Capacities     

2

    Warning     

2

2  BEFORE YOU BEGIN     

3-6

    Parts Bags for ‘step by step’ assembly     

3

    Exploded drawing     

4

    Pre-Assembly Check List     

5

    Unpacking Information     

6

3 ASSEMBLY 

7-11

4  COMPUTER     

12

    Computer Instructions     

12-18

    Computer Button Functions     

18

5  CUSTOMER INFORMATION 
    Customer Service 

back cover

The parts required for each step of the 
assembly process are sorted by step 
in individual zip bags as shown left. 
Each step has required parts and each 
of those parts is included with the bag 
printed with the assembly step.

It is recommended that these parts not 
be removed from the individual bags 
until each step of the process to avoid 
mixing up or confusing parts.

If you find that you are missing parts or 

the bag for a step is missing, please 
contact Helix or your dealer to receive 
those items. You can refer to the parts 
by the “step number” for ease of 
description.

  2 

PARTs bAgs FOR ‘sTeP by sTeP’ AssembLy 

  2 

TAbLe OF COnTenTs 

PAGE 3

 

HLT2500.indd   3

04/10/2015   19:09

Содержание HLT2500





















Отзывы: