manualshive.com logo in svg

Heliocol SHC-ITS-HC30, Руководство по установке, Страница: 2 / 30

Поделиться
Скачать
Heliocol SHC-ITS-HC30 Скачать руководство пользователя страница 2

Contents

1 Introduction .........................................................1 

Overview .................................................................1 

Conventions used in this Guide ............................ 2 

Safety precautions ................................................. 2 

2 Basic Heliocol Terminology................................3 

3 Designing your system ........................................4 

Deciding on the location for the panels..................4 

Preparing a schematic diagram ...............................5 

Sample collector system ..........................................6 

Mounting racks .........................................................7 

4 Parts and tools .....................................................8 

Heliocol fittings and accessories .............................9 

5 Hydraulics...........................................................11 

Panel configurations ...............................................11 

Guidelines for residential installations ..................11 

Basic plumbing & array layouts .............................12 

Plumbing ..................................................................13 

Balanced flow ...........................................................13 

Pump power ..............................................................14 

Booster Pumps.............................................................14 

Automatic drainage ..................................................15 

6 Installation...........................................................16 

Connecting panels together .....................................16 

Bypassing a small obstruction .................................18 

Connecting panels across a large obstruction ........18 

7 Connecting to the existing equipment ...........19 

Feed and return lines..................................................19 

Connecting with the existing filtration system .......20 

Plumbing guidelines ..................................................21 

Automatic systems (Private & public pools)...........22 

8 Operation............................................................24 

Turning the system on (manual systems) ................24 

Turning the system off (manual systems) ...............24 

9 Troubleshooting.................................................25

 

10 Replacing a damaged riser tube...................27 

Содержание SHC-ITS-HC30































Отзывы:

Нет отзывов