background image

TABLE OF CONTENTS

    

 

Safety and General Information   

 

 

 

 2

   

 

 

Product Description & Specifications 

 

 

 

 2

 

 

  Assembly/Preparation 

      

3

 

 

  Operation 

       

8

 

 

  Maintenance 

      11

 

 

  Troubleshooting 

 

 

 

     12

 

 

  Warranty       12

2

SAFETY AND GENERAL INFORMATION

Save these instructions. 

For your safety, read, understand, and follow the information provided with and on this device 

before using. The owner and/or operator shall have an understanding of the device, its operating characteristics and 

safety operating instructions before operating the equipment. The owner and/or operator shall be aware that use and 

repair of this product may require special skills and knowledge. Instructions and safety information shall be read to and 

discussed with the operator in the operator's native language, making sure that the operator comprehends their contents, 

before use of this equipment is authorized. If any doubt exists as to the safe and proper use of this device, remove from 

service immediately. 

Inspect before each use.

 Do not use if abnormal conditions such as cracked welds, damaged, loose or missing parts 

are noted. Any equipment that appears damaged in any way, is found to be worn, or operates abnormally shall be 

removed from service until repaired. If the equipment has been or is suspected to have been subjected to an abnormal 

load or shock, immediately discontinue use until inspected by a factory authorized repair facility (contact distributor or 

manufacturer for list of authorized repair facilities). It is recommended that an annual inspection be made by an authorized 

repair facility. Labels and Operator's Manuals are available from the manufacturer. 

• Study, understand and follow all instructions before operating this device.
• Do not exceed rated capacity.
• Use only on hard, level surface.
• Before moving, lower the load to the lowest possible point.
• Use only slings or chains with a rated capacity greater than the weight of the load being lifted.
• Do not allow load to swing or drop violently while lowering or moving.
• No alterations shall be made to this product.
• Failure to heed these markings may result in personal injury and/or property damage.

!

   

WARNING

!  

 

DANGER

!  

 

CAUTION

!  

 

WARNING

NOTICE

SIGNAL WORDS

Indicates situation which, if not avoided, 

will result in death or serious injury

Indicates situation which, if not avoided, 

could result in death or serious injury

Indicates situation which, if not avoided, 

could result in minor or moderate injury

Indicates situation which, if not avoided, 

could result in damage to property

Содержание HW93809

















Отзывы: