HEIDENHAIN TNC 370 D Скачать руководство пользователя страница 60

Страница: 60 / 92

July 02

Machine Parameters

TNC 370 D

4–57

4.4 Positioning

Machine
parameter

Function and input

Change via

Reaction

MP1010.0-3 Rapid

traverse

Input:

80 to 300 000 [mm/min]

PLC

MP1020.0-3

Manual feed rate
Input:

80 to 300 000 [mm/min]

PLC

MP1030.0-3 Positioning

window

Input:

0. 001 to 2.000 [mm]

PLC

MP1040

Polarity of the nominal value voltage for the
positive traverse direction
Input: %xxxx
Bit

0 to 3

0 = not active

Axis

X to 4

1 = active

Reset

MP1050.0-3

Analog voltage for rapid traverse
Input:

1.000 to 9.000 [V]

PLC

MP1060.0-3 Acceleration

Input:

0.001 to 20.000 [m/s

]

PLC

MP1070.0

Radial acceleration
Input:

0.001 to 20.000 [m/s

]

PLC
RUN

MP1070.1

Acceleration at contour transition elements
Input:

0.001 to 20.000 [m/s

]

PLC
RUN

MP1080.0-3 Integral

factor

Input:

0 to 65 535

PLC
RUN

MP1090

Jerk limiting on the contour
Input:

0 to 1000 [m/s³]

0 = no jerk limiting (MP 1520 active)
1 to 1000 jerk limiting

MP1097.0-3

Axis-specific jerk limit
(active only with M112 and MP7415.1 bit 2)
Input:

1 to 1000 [m/s

]

Recommended input value 10 to 50

MP1099

Filter order for nominal position value filter
Input: 0 to 7
0 = no filter
1 to 7 filter order
Recommended input value 1 to 3

MP1110.0-3 Standstill

monitoring

Input:

0.001 to 30.000 [mm]

PLC

MP1140.0-3

Movement monitor on
Input:

0.030 to 10.000 [V]

PLC
RUN

Содержание TNC 370 D





























































































Результаты поиска

Содержание TNC 370 D

Отзывы:

Похожие инструкции для TNC 370 D

Бренды по названию

Популярные бренды

HEIDENHAIN TNC 370 D, Техническая информация

Результаты поиска

Содержание TNC 370 D

Отзывы:

Похожие инструкции для TNC 370 D

Бренды по названию

Популярные бренды