HeatStar HSVFBF10LP страница 1 Скачать руководство пользователя

Страница: 1 / 16

Installation Instructions and Owner’s Manual

Unvented Liquid Propane Fired Room Heater

Heatstar Products, Inc., 4560 W. 160

ST., CLEVELAND, OHIO 44135 · 866-447-2194

2017- CB

OPERATING INSTRUCTIONS

AND OWNER’S MANUAL

READ INSTRUCTIONS CAREFULLY:

Read and follow all instructions. Place instructions in a safe

place for future reference. Do not allow anyone who has not read these instructions to assemble,
light, adjust or operate the heater.

Model #

Blue Flame Heaters

HSVFBF10LP

Plaque Heaters

HSVFRD10LP

HSVFBF10LP

WARNING:

If the information in this manual is not followed exactly, a fire or explosion may result causing

property damage, personal injury, or loss of life.

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS

• Shut off gas supply

• Do not try to light any appliance

• Do not touch an electrical switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency, or the gas supplier.

WARNING

: This is an unvented gas-fired heater. It uses air (oxygen) from the room in which it is installed.

Provisions for adequate combustion and ventilation air must be provided. Refer to Fresh Air for Combustion and

Ventilation section on page 4 of this manual.

WARNING

: Improper installation, adjustment, alteration, service or maintenance can cause injury or property

damage. Refer to this manual for correct installation and operational procedures. For assistance or additional

information consult a qualified installer, service agency, or gas supplier.

INSTALLER: Leave this manual with the appliance. CONSUMER: Retain this manual for future reference.

UNVENTED LP-GAS FIRED ROOM HEATER

This appliance may be installed in an aftermarket permanently manufactured (mobile) home, where not prohibited

by local codes. This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not

convertible for use with any other gas.

Содержание HSVFBF10LP

















Результаты поиска

Содержание HSVFBF10LP

Отзывы:

Похожие инструкции для HSVFBF10LP

Бренды по названию

Популярные бренды

HeatStar HSVFBF10LP, Инструкция по эксплуатации и руководство пользователя

Результаты поиска

Содержание HSVFBF10LP

Отзывы:

Похожие инструкции для HSVFBF10LP

Бренды по названию

Популярные бренды