background image

6

SAFETY PRECAUTIONS

Read and understand all precautions before operating 
the furnace.

Save these instructions. Retain this manual as long 
as you own your Heatmaster

SS

 furnace. Carefully 

read and follow these directions.

IMPORTANT

THESE FURNACES ARE FOR COAL BURNING ONLY. 
Follow all applicable local laws.

DANGER

Do not start fire with or burn chemicals, volatile fluids, 
rubber, plastics or garbage. Only competent persons 
with a sound understanding of this heating method 
should operate this furnace. Improper firing could 
result in personal injury and or damage to the unit 
and void warranty.

Risk of fire or explosion

•  Do not use chemicals or fluids to start the fire.
•  Do not burn garbage, gasoline, drain oil or other 

flammable liquids.

•  Do not operate with fuel loading or ash removal 

doors open

•  Do not store fuel or other combustible material 

within marked installation clearances

•  Inspect and clean flues and chimney regularly
•  Maximum draft marked on nameplate
•  DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE 

SERVING ANOTHER APPLIANCE

WARNING

•  All installations and operations of your 

HEATMASTER SS product must follow STATE, 
PROVINCIAL, and LOCAL LAWS pertaining to 
operations, wiring, plumbing and building codes.

•  All models operate at atmospheric pressure. DO 

NOT obstruct, block or plug the overflow vent tube 
in any way which is located on top of the boiler 
either in front of or behind the chimney.

•  When installing the furnace, the chimney should 

never be connected to a chimney flue serving 
another appliance.

•  Do not start a fire in the furnace without first filling 

with water. It will cause serious damage to the 
furnace.

•  All covers or guards must be in place at all times, 

except for maintenance or service.

ATTENTION

•  A copy of the owner’s manual in French is 

available by request from Heatmaster

SS

 offices.

•  The person(s) operating this furnace must comply 

with all applicable local and state laws or other 
requirements,

•  Do not remove labels from furnace except in the 

case of servicing.

CAUTION

•  Use of an approved spark arrester is 

recommended. It is the recommendation of 
SteelTech Inc that a 15’ minimum distance of 
clearance from buildings and other combustibles. 
Your local authorities and your insurance company 
may require a greater distance. Never allow 
combustible material to accumulate near the unit. 
Fuel should never be stored where there is the 
potential for accidental fire.

•  Load carefully or damage will result.
•  Do not use chemicals or fluids to start the fire.
•  Do not start or operate furnace without checking 

heating fluid. Furnace must be filled until heating 
fluid comes out of vent pipe on the top of the 
furnace.

• 

Hot Surfaces: 

Keep children away. Do not touch 

during operation.

RECOMMENDED

Choose the location of your furnace with concerns of 
wind direction, smoke odor, sparks, blocked viewing 
and fuel storage carefully. Be a responsible and 
considerate owner.

Содержание C-150

























Отзывы: