background image

COMMUNITY BARBECUE

 

1

8

A-0060-MAN Heatlie Community Barbecue Instruction Manual V2 Updated Dec 2021

Heatlie Barbecues warrants its products to be free of original 
manufacturing defects in material and workmanship, for a period of ten 
(10) years from the date of purchase for domestic use and one (1) year for
commercial use. Any claim must be made within this time, dating from the
date of purchase.

Our goods come with guarantees that cannot be excluded under 
Australian Consumer Law. You are entitled to a replacement or refund for 
major failure and for compensation for any other reasonably foreseeable 
loss or damage. You are also entitled to have the goods repaired or 
replaced if the goods fail to be of acceptable quality and the failure does 
not amount to major failure.

This warranty is subject to the following conditions:

1. The warranty applies to the original owner provided the original date of

purchase can be verified or the warranty card has been completed and
returned to Heatlie.

2. The owner has the responsibility of adequately packaging the product

and transporting it under insurance to place of purchase, or to Heatlie
Barbecues, at the owner’s cost.

3. Warranty service must be performed by a Heatlie authorised gas fitter

or by Heatlie Barbecues.

4. Installation must conform to the applicable gas and building standards

laid down by the country or state, and according to the Heatlie product
installation guide and instructions.

5. This warranty policy does not cover problems associated with corrosion.
6. This warranty policy does not cover buckling or warping of the hotplate.
7. Lack of maintenance, abuse, misuse, neglect, accident or improper

installation of the appliance will not be covered.

8. Corrosion or damage caused by exposure to the elements, insects,

weather or hail will not be covered under this warranty.

NOTE:

  ALL BARBECUES MUST BE COVERED BY A WEATHERPROOF

COVER WHEN NOT IN USE

9.

Any evidence that the product has been modified or serviced by an
unauthorised person will void the warranty.

10.

Heatlie authorised gas fitters may provide on-site warranty service. No
other costs shall be covered by warranty other than the costs of parts
and labour.

11.

Spare parts are only available from Heatlie 

Barbecues

.

In the event that warranty service is required, contact the place of 
purchase. No other warranties, either expressed or implied, whether by 
distributor, retailer or employees of Heatlie, will be recognised or honoured 
by Heatlie. 

This limited warranty sets forth the sole remedy of the owner. The 
total liability of Heatlie is limited to the purchase of the product. 
Heatlie are continually updating and improving their products, 
therefore details and specifications are subject to change.

WARRANTY 
POLICY

Содержание COMMUNITY BARBECUE CBBQ 600




















Отзывы: