background image

GENERAL INSTALLATION INSTRUCTIONS

HEATITCABLE.COM

5

4.  Install pump onto the backwater pipe, using the 3/4” female fitting and gasket ensuring

     that the pump shaft is horizontal. The pump should be installed so that the pump is 

     pumping away from the hot water heater, towards the house. Confirm the direction 

     of pumping by observing the flow arrow on the side of the pump housing. Be sure that 

     the pump is not touching the exhaust vent piping (chimney) of a gas or oil-fired hot 

      water heater. (See Picture #2)

5.  Connect the backwater line to the 3/4” NPT inlet of the pump. Use pipe dope or Teflon

     tape to seal threads when connecting to a 3/4 female NPT connection. If a gasket 

     flexible copper water heater connector is used pipe dope or Teflon tape is not required. 

6.  Reopen the supply valve to the hot water heater and allow the water to run until all the

     air has been purged from the piping.

7.  Close faucet inside the house. page 2 Picture 1 Disconnect Direction of water

8.  Plug the line cord of the pump into a 115V outlet. Be sure to route the power cord so 

     that it does not touch the exhaust vent piping of a gas or oil-fired hot water heater. 

Key points of installation: remember to open the valve of cold 

water pipe/hot water pipe/return pipe after installation.

DO NOT Mount Motor Shaft in Vertical Position

Commissioning

Panel description

Function description

Mold name

Mold description

  Smart constant 

temperature mode

Energy-saving constant 

    temperature mode

Manual mode

When turned on, the       icon lights orange, and the pump operates at constant 

temperature throughout a day.

When turned on, the     icon lights green, and the pump operates at an energy-saving 

constant temperature state throughout a day.HEATIT Smart pump can decrease the 

temperature setting point automatically if you didn’t use the hot water for some time.

When pressing the     icon briefly in any state, the pump will stop after reaching the set 

time or target temperature.

Function name

Function description

Mode switch

Pump speed switch

Antifreeze protection

Smart constant temperature mode (orange light), energy-saving constant temperature 

mode (green light), Manual mode (no light).

The product is divided into three gears. When running, the gear is indicated by the 

rotating speed of the light bar. The faster the rotating speed is, the higher the gear is.

When the water temperature of the pipeline is lower than 5

 for 30s, the electric pump 

will operate until the water temperature meets 10C. If the water temperature can’t meet 

10C, a buzzer will sound to give an alarm.

Speed

Mode Set

Picture 2 

Содержание HIP 24-12A







Отзывы: