Heatilator NBV3630 Скачать руководство пользователя

Страница: 28 / 56

Heatilator • Novus NBV • 4055-188 Rev C • 04/08

Latches

(both bottom

and top)

Glass

Assembly

Figure 12.11 Glass Assembly

M. Install Floor Cover

Install the

oor cover as shown in Figure 12.10.

N. Fixed Glass Assembly

Removing Fixed Glass Assembly

WARNING! Risk of Asphyxiation!

Handle

xed glass as-

sembly with care. Inspect the gasket to ensure it is undam-
aged and inspect the glass for cracks, chips or scratches.

DO NOT:

• Strike, slam or scratch glass
• Operate

replace with glass removed, cracked, bro-

ken or scratched.

Replace

xed glass assembly as a complete assembly.

• Remove

screen.

• Pull the four (30/33/36 in. appliances) or seven (42 in.

appliance) glass assembly latches out of the groove on
the glass frame. Refer to Figure 12.11.

• Remove the glass assembly from the appliance.

Replacing Fixed Glass Assembly

• Set the glass panel on the lower two or four glass assembly

latches, ensuring the glass panel is centered in the
opening.

• Replace

screen

O. Close the Screen Assembly

Rotate the screen closed. See Figures 12.12 and 12.13.

Figure 12.10 Installing Floor Cover

Figure 12.12 Closing Screen

Figure 12.13 Closing Screen

Note:

The

oor cover in the bottom front of the

replace

may be covering the UL labels. It is loose and can be
removed/replaced.

Содержание NBV3630

























































Результаты поиска

Содержание NBV3630

Отзывы:

Похожие инструкции для NBV3630

Бренды по названию

Популярные бренды

Heatilator NBV3630, Руководство пользователя

Результаты поиска

Содержание NBV3630

Отзывы:

Похожие инструкции для NBV3630

Бренды по названию

Популярные бренды