Heatilator LM42 Скачать руководство пользователя

Страница: 30 / 44

Heatilator • LM42 • Installers Manual • 4087-901 • Rev A • 04/14/16

Figure 5.16 Installing CT-3A-B Adapter

Chimney

Pipe

Chase Top

Termination Cap

Chase

Collar

2 in. (51 mm)

Minimum Height

Place waterproof sealer under

each flange of the termination

cap and on top of each screw

to help prevent leaks.

2 in. (51 mm)

maximum

4 3/4 in. (121 mm)

maximum

The last section of pipe must

stop between 2 in. (51 mm)

above the top of the chase and

4 3/4 in. (121 mm) below the

top of the chase.

Figure 5.14 Installing a TS345/TS345P Square Termination Cap

Figure 5.15 Installing a TCT375 Terra Cotta Cap

Chimney

Pipe

Chase Top

Termination Cap

Chase

Collar

2 in. (51 mm)

Minimum Height

Remove 2 screws

from front & back

to lift the top off

Place waterproof sealer

under each flange of the

termination cap and on

top of each screw to

help prevent leaks.

The last section of pipe

must stop between 2 in.

(51 mm) above top of

chase and 4-3/4 in. (121

mm) below top of chase

2 in. (51 mm)

4-3/4 in. (121 mm)

Storm Collar

Chimney

Pipe

Chase Top

Termination

Cap (not shown)

Chase

Collar

2 in. (51 mm)

Minimum Height

Caulk gaps between

storm collar & pipe,

and storm collar

& chase top.

Do NOT block

air holes

3 clip brackets.

Slip over chase collar

and attach with screws

provided.

Assemble

storm collar

around extended

termination cap

pipe

once cap is

installed.

4-3/4 in. (121 mm)

2 in. (51 mm)

The last section of pipe must stop

between 2 in. (51 mm) above the

top of the chase and 4 3/4 in. (121

mm) below the top of the chase.

Содержание LM42













































Результаты поиска

Содержание LM42

Отзывы:

Похожие инструкции для LM42

Бренды по названию

Популярные бренды

Heatilator LM42, Руководство по установке

Результаты поиска

Содержание LM42

Отзывы:

Похожие инструкции для LM42

Бренды по названию

Популярные бренды