Heatilator LM42 Скачать руководство пользователя

Страница: 24 / 44

Heatilator • LM42 • Installers Manual • 4087-901 • Rev A • 04/14/16

NOTICE:

Chimney sections cannot be disassembled once

locked together. Plan ahead!

• Lock chimney sections and/or offsets/returns together by

pushing downward until the top section meets the stop

bead on the lower section.

• Pull on the top of each section as installed to make sure

it is fully engaged and will not separate.

• You may use #6 or #8 sheet metal screws no longer

than 1/2 in. (13 mm) to fasten chimney outer sections

together. Do NOT penetrate inner flue.

• Vertical straight runs of chimney must be supported every

35 ft (10.7 m).

B. Assemble Chimney Sections

Use only those components described in this manual.

Attach either a straight chimney section or an offset to the

top of the fireplace starting with the inner flue followed by

the outer casing. Continue this order until termination cap

is reached (depending on your installation requirement).

Chimney sections are locked together by pushing down

ward until the top section meets the stop bead on the lower

section.

The inner flue is placed to the inside of the flue section be

low it. The outer casing is placed outside the outer casing

of the chimney section below it. See Figure 5.3.

WARNING! Risk of Fire! DO NOT

install substitute or

damaged chimney components.

Figure 5.3 Assembling Chimney Sections

C. Secure Offset/Return

When offsets and returns are joined to straight pipe sec

tions, they must be locked into position with the screws

(outer only). To prevent the chimney sections from from

pulling apart, the returns and the chimney stabilizers have

hanger straps for securing these parts to joists or rafters.

See Figure 5.4.
* Use # 6 or # 8 sheet metal screw, or larger, no longer

than 1/2 in. (13 mm).

WARNING! Risk of Fire!
• Secure offsets with screws (not to exceed 1/2 in./13 mm

In length).

• Secure returns with strapping.

• Straight chimney sections may be secured with screw

(not to exceed 1/2 in./13 mm In length) at the joints.

• Keep chimney sections from separating or twisting.

Ceiling

Firestop

Straps

Optional

Additional

Support

Joint

Band

(Optional)

Figure 5.4 Secure the Chimney

Section 5

Содержание LM42













































Результаты поиска

Содержание LM42

Отзывы:

Похожие инструкции для LM42

Бренды по названию

Популярные бренды

Heatilator LM42, Руководство по установке

Результаты поиска

Содержание LM42

Отзывы:

Похожие инструкции для LM42

Бренды по названию

Популярные бренды