Heatilator ICON100IH Скачать руководство пользователя

Страница: 19 / 68

Heatilator • ICON DV • 4042-300 Rev R • 06/07

1-1/2 in.
(38 mm)

3 in.

(76 mm)

No combustible
framing to be
located within
shaded area.

2 x 4 or
2 x 6
header

Sheetrock

B. Wall Penetration Framing

• Frame a hole in a combustible wall for a wall shield

restop

(Figures 6.1 through 6.3) whenever a wall is penetrated.
Use same size framing materials as those used in the wall
construction. The wall shield

restop maintains minimum

clearances and prevents cold air in

ltration.

• If the hole being penetrated is surrounded by non-

combustible materials such as concrete, a hole with
diameter 1 in. greater than the pipe is acceptable.

A. Pipe Clearances to Combustibles

Fire Risk
Explosion Risk
Maintain vent clearance to combustibles as
speci

ed.

• Do not pack air space with insulation or

other materials.

Failure to keep insulation or other materials
away from vent pipe may cause

re.

WARNING

Figure 6.1 Pipe Clearances

3 in. (76 mm)
top clearance

1 in. (25 mm)clearance

bottom & sides

1 in. (25 mm)
clearance
around vertical
sections

3 in. (76 mm)
top clearance

1 in. (25 mm)
clearance
bottom & sides

Heat
Shield

Wall

Shield

Firestop

Heat
Shield

WALL

Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm).

The

heat shield is designed to be used on a wall 4 in. to 7-1/4 in. (102 mm to
184 mm) thick.

If wall thickness is less than 4 in. (102 mm) the existing heat

shields must be field trimmed. If wall thickness is greater than 7-1/4 in. (184
mm) a DVP-HSM-B will be required.

Figure 6.2 Horizontal Venting Clearances to Combustible Materi-

als

Framing should be
constructed of 2 X 4
lumber or heavier.

The center of the
framing hole is
1 in. (25mm) above
the center of the
horizontal vent pipe.

Vent framing hole.
DO NOT PACK WITH
INSULATION OR
OTHER MATERIAL.

* Measured to
center of pipe.

10 in.

12 in.

Figure 6.3 Exterior Wall Hole

Vent Clearances and Framing

Appliance

ICON60IT

64-1/8 in./1629 mm

ICON60ILT

64-1/8 in./1629 mm

ICON60IH

64-1/8 in./1629 mm

ICON60ILH

64-1/8 in./1629 mm

ICON100IT

68-5/8 in./1743 mm

ICON100ILT

68-5/8 in./1743 mm

ICON100IH

68-5/8 in./1743 mm

ICON100ILH

68-5/8 in./1743 mm

Содержание ICON100IH





































































Результаты поиска

Содержание ICON100IH

Отзывы:

Похожие инструкции для ICON100IH

Бренды по названию

Популярные бренды

Heatilator ICON100IH, Руководство пользователя

Результаты поиска

Содержание ICON100IH

Отзывы:

Похожие инструкции для ICON100IH

Бренды по названию

Популярные бренды