Heatilator CST42A Скачать руководство пользователя

Страница: 30 / 48

Heatilator • CST42A • 4012-012 Rev J • 08/06

I. Starting a Fire

Check the

ue damper to be certain it is in the full open po-

sition. Place crumpled or twisted paper under the

replace

grate. Loosely arrange kindling or small pieces of wood to
form a layer above the paper.

The

res must be built on the

replace grate, without danger

of the burning fuel falling out of the

replace opening.

Light the paper and add small pieces of wood until a hot bed
of embers has been established.

After establishing the

re bed, and the small

rewood is burn-

ing briskly, add a minimum of three average sized pieces of
split

rewood, place the wood in such a manner to allow

combustion air and

ames between them.

Note:

The

rst three or four

res should be of moderate

size to allow the oils and binders to be burned from the

replace and the refractory and paint to cure. You may

notice an industrial odor the

rst few

res. This is consid-

ered normal.

Note:

When

rst lighting your

replace, it may be neces-

sary to pre-warm the

ue to establish a draft. This is done

by holding a rolled up piece of burning newspaper under
the

ue damper for a few moments. This will help reduce

smoke spillage during start-up.

Odors and vapors released during initial
operation.
• Curing of high temperature paint.
• Open windows for air circulation.
Odors may be irritating to sensitive individuals.

CAUTION

Fire Risk

Keep combustible materials, gasoline and
other

ammable vapors and liquids clear of

replace.

• Do NOT store

ammable materials close

to the

replace.

• Do NOT use gasoline, lantern fuel,

kerosene, charcoal lighter

uid or similar

liquids to start or “freshen up” a

re in this

replace.

• Keep all such liquids well away from the

replace while it is in use.

Combustible materials may ignite.

WARNING

Содержание CST42A

















































Результаты поиска

Содержание CST42A

Отзывы:

Похожие инструкции для CST42A

Бренды по названию

Популярные бренды

Heatilator CST42A, Руководство пользователя

Результаты поиска

Содержание CST42A

Отзывы:

Похожие инструкции для CST42A

Бренды по названию

Популярные бренды