Heatilator CST42A Скачать руководство пользователя | Manualshive

Страница: 18 / 48

background image

Heatilator • CST42A • 4012-012 Rev J • 08/06

18

B. Using Offsets/Returns

To bypass any overhead obstructions, the chimney may be
offset using a 30-deg (SL430) offset/return.

An offset and return may be attached together or a chimney
section(s) may be used between an offset and return.

Perform the following steps to determine the correct chim-
ney component combination for your particular installation:

• Measure how far the chimney needs to be shifted to enable

it to avoid the overhead obstacle. See Figure 5.3. Use
dimension “A” to determine chimney section required to
achieve the needed shift.

• After determining the offset dimension, refer to Table 5.2

and

fi

nd the “A” dimension closest to but not less than the

distance of shift needed for your installation.

• The “B” dimension that coincides with the “A” dimension

represents the required vertical clearance that is needed
to complete the offset and return.

• Read across the chart and

fi

nd the number of chimney

sections required and the model number of those particular
chimney parts.

• Whenever the chimney penetrates a

fl

oor/ceiling, a ceiling

fi

restop must be installed.

• The effective height of the

fi

replace assembly is measured

from the base of the

fi

replace to the top of the starter collar.

See Dimensions in Section 12.

Table 5.2

A

B

1-1/4 in. (32 mm)

OVERLAP

Figure 5.3 Chimney Offset/Return

Example:

Your “A” dimension from Figure 5.3

is 14 1/2 in. (368 mm). Using Table 5.2 the
dimension closest to, but not less than 14 1/2 in.
(368 mm) is 15 3/4 in. (400 mm) using a 30°
offset/return. It is then determined from the table
that you would need 36 5/8 in. (930 mm) (Dimen-
sion “B”) between the offset and return. The
chimney components that best

fi

t your application

are two SL412s.

Fire Risk

• Draft will be restricted if offset/returns

greater than 30° are used.

WARNING

A

B

SL406

SL412

SL418

SL436

SL448

in.

mm

in.

mm

4 7/8

124

17 7/8

454

-

-

-

-

-

7 1/4

184

2 2

559

1

-

-

-

-

9 3/4

248

26 1/8

664

2

-

-

-

-

10 1/4

260

27 1/4

692

-

1

-

-

-

12 3/4

324

31 3/8

797

1

1

-

-

-

13 1/4

337

32 3/8

822

-

-

1

-

-

15 3/4

400

36 5/8

930

-

2

-

-

-

18 1/8

460

40 3/4

1035

1

2

-

-

-

18 3/4

476

41 3/4

1060

-

1

1

-

-

21 3/4

552

4 7

1194

-

-

2

-

-

22 1/4

565

48

1219

-

-

-

1

-

24 3/4

629

52 1/8

1324

1

-

-

1

-

27 3/4

705

57 3/8

1457

-

1

-

1

-

28 1/4

718

58 3/8

1483

-

-

-

-

1

30 3/4

781

62 1/2

1588

1

-

-

-

1

33 3/4

857

67 3/4

1721

-

1

-

-

1

36 3/4

933

7 3

1854

-

-

1

-

1

39 3/4

1010

78 1/8

1984

-

-

-

2

-

41 1/8

1045

82 3/8

2092

1

-

-

2

-

45 3/4

1162

88 1/2

2248

-

-

-

1

1

48 1/8

1222

92 3/4

2356

1

-

-

1

1

51 3/4

1314

98 7/8

2511

-

-

-

-

2

Proper assembly of air cooled chimney parts results in an overlap of chimney joints
of 1-1/4 in. (32 mm). Effective length is built into this table.

¨

¨

«
...
16
17
18
19
20
...
»

Содержание CST42A

















































Отзывы:

Нет отзывов

Похожие инструкции для CST42A

Бренд: Glow Fire Страницы: 101

Бренд: Napoleon Страницы: 40

Бренд: Bali Страницы: 16

Naples GF301525BK

Бренд: Moda flame Страницы: 7

Fire Ribbon Direct VEnt Slim 26"

Бренд: Spark Страницы: 48

Бренд: ELEMENTI Страницы: 20

Бренд: JAYLINE Страницы: 16

Бренд: Lopi Страницы: 11

Crestline LSBV-3628EN

Бренд: Lennox Страницы: 20

Cabinets Classic Series

Бренд: Majestic fireplaces Страницы: 4

Бренд: Heat&Glo Страницы: 3

Masonry Fireplace Enclosure

Бренд: CMC Страницы: 4

Бренд: Nibe Страницы: 20

Fire Island GAD15410M

Бренд: MR. BAR-B-Q Страницы: 22

Бренд: Cello Страницы: 18

Askja 235.17-AUT

Бренд: Haas+Sohn Страницы: 10

Premier Estate PEVFR18LP

Бренд: SHM Страницы: 24

Бренд: Town & Country Fireplaces Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды