Heatilator CNXT4236IH-D Скачать руководство пользователя страница 57

Страница: 57 / 78

Heatilator • CNXT4236IT-D, CNXT4842IT-D, CNXT4236IH-D, CNXT4842IH-D • 2360-900 Rev. i • 5/17

A. Remove Fixed Glass Assembly

See Section 14.H.

B. Remove the Shipping Materials

Remove shipping materials from inside or underneath the

firebox.

Appliance Setup

Rock wool

placement

(shaded areas)

Vermiculite and

lava rock

placement on

sides and front

of hearth pan.

Vermiculite and

lava rock

placement on

sides and front

of hearth pan.

BURNER

Figure 14.2 Placement of Embers

Figure 14.1 Placement of Embers

C. Clean the Appliance

Clean/vacuum any sawdust that may have accumulated

inside the firebox or underneath in the control cavity.

D. Accessories

Install approved accessories per instructions included

with accessories. Contact your dealer for a list of ap-

proved accessories.

WARNING!

Risk of Fire and Electric Shock!

Use ONLY

Hearth & Home Technologies-approved optional acces-

sories with this appliance. Using non-listed accessories

could result in a safety hazard and will void the warranty.

E. Ember Placement

WARNING!

Risk of Explosion!

Follow ember place

ment instructions. DO NOT place ember directly over

burner ports. Replace ember material annually. Improp-

erly placed ember material interferes with proper burner

operation.

Place the Ember Material

See Figures 14.1 and 14.2. Place a small amount of

1/2 in. diameter pieces (dime-size) of ember material on

the burner top. Be careful not to cover burner ports. It is

not necessary to use the entire bag. Save the remaining

amount for future use.

WARNING!

Risk of Explosion!

Follow ember placement

instructions. DO NOT place embers directly over burner

ports. Replace ember material annually. Improperly placed

embers interfere with proper burner operation.

Ember material is shipped with this gas appliance. To place

the ember material:
• Embers CANNOT be placed directly over ports. Care

should be taken not to cover the lighting trail of ports

(from back to front).

• Place dime-size pieces of Glowing Embers® just in front

of the port trail, but not on or in between the ports (see

Figure 14.2). Care should be taken so that the ports are

not covered. Failure to follow this procedure will likely

cause lighting and sooting problems.

Содержание CNXT4236IH-D















































































Результаты поиска

Содержание CNXT4236IH-D

Отзывы:

Heatilator CNXT4236IH-D, Руководство пользователя, Страница: 57 / 78

Результаты поиска

Содержание CNXT4236IH-D

Отзывы: