Heatilator BIR42-B Скачать руководство пользователя страница 34

Страница: 34 / 44

Heatilator • Birmingham 42-B Installation Manual • 4059-715 • Rev P • 09/28/15

Fireplace Setup

A. Install Hearth Molded Brick Panel

• Place hearth panel into the fireplace.

B. Install Back Molded Brick Panel

• Remove screen rods.

• Remove smoke shield.

• Refer to Figure 8.1.

• Set the grate brackets in place, 26.5 in. (673 mm) center

to center.

• Install the back panel. Center from side to side.

• Install two refractory clips in the mortar lines across the

top. Tighten these and all previously installed brackets.

C. Install Side Molded Brick Panel

• If a gas line is to be installed, remove the knockouts in

the inner firebox and in the outer shell on the side of

your choice. Refer to dimension drawings for location of

knockouts and Section 8.I. for gas provisions.

• Install side panel, tapered edge to the front. Align the

front edge with the front of the column (or butted to the

surround if installed).

• Install two refractory clips in the mortar lines across the

top. Tighten these and all previously installed brackets.

• Install second side panel following the steps above.

• Replace smoke shield.

Figure 8.1 Traditional Molded Brick Panel

LH Traditional

Refractory

Back Traditional

Refractory

Hearth

Grate

Retainer

Refractory

Clips

LH Herringbone

Refractory

Back Herringbone

Refractory

Hearth

Grate

Retainer

Refractory

Clips

Figure 8.2 Herringbone Molded Brick Panel

Содержание BIR42-B













































Результаты поиска

Содержание BIR42-B

Отзывы:

Похожие инструкции для BIR42-B

Бренды по названию

Популярные бренды

Heatilator BIR42-B, Руководство по установке

Результаты поиска

Содержание BIR42-B

Отзывы:

Похожие инструкции для BIR42-B

Бренды по названию

Популярные бренды