Heatilator BIR42-B Скачать руководство пользователя страница 7

Страница: 7 / 44

Heatilator • Birmingham 42-B Installation Manual • 4059-715 • Rev P • 09/28/15

2. Locating Fireplace & Chimney

Location of the fireplace and chimney will affect perfor-

mance.
• Install within the warm airspace enclosed by the building

envelope. This helps to produce more draft, especially

during lighting and die-down of the fire.

• Installing the fireplace in a basement is not recommended.

• Penetrate the highest part of the roof. This minimizes

the effects of wind loading.

• Locate termination cap away from trees, adjacent

structures, uneven roof lines and other obstructions.

• Minimize the use of chimney offsets.

• Consider the fireplace location relative to floor and ceiling

and attic joists.

• Take into consideration the termination requirements in

Section 5.

Marginal Location:

• Below peak

Location NOT recommended:

• Not the highest point of the roof

• Wind loading possible

Multi-level Roofs

Windward

Leeward

Recommended Location:

• Above peak

Recommended:

• Insulated exterior chase

in cooler climates

Recommended Location:

• Above peak

• Inside heated space

Location NOT recommended:

• Too close to tree

• Below adjacent structure

• Lower roof line

• Avoid outside wall

Marginal Location:

• Wind loading possible

Not recommended in lower level due

to high negative pressure concerns

that effect draft

Figure 2.3 Recommended Chimney Locations

• Install the outside air kit with the intake facing prevailing

winds during the heating season.

• Ensure adequate outdoor air for all combustion

appliances and exhaust equipment.

• Ensure furnace and air conditioning return vents are not

located in the immediate vicinity of the fireplace.

• Avoid installing the fireplace near doors, walkways or

small isolated spaces.

• Recessed lighting should be a “sealed can” design.

• Attic hatches weather stripped or sealed.

• Attic mounted duct work and air handler joints and seams

taped or sealed.

Содержание BIR42-B













































Результаты поиска

Содержание BIR42-B

Отзывы:

Похожие инструкции для BIR42-B

Бренды по названию

Популярные бренды

Heatilator BIR42-B, Руководство по установке

Результаты поиска

Содержание BIR42-B

Отзывы:

Похожие инструкции для BIR42-B

Бренды по названию

Популярные бренды