Heatilator BIR42-B Скачать руководство пользователя страница 2

Страница: 2 / 44

Heatilator • Birmingham 42-B Installation Manual • 4059-715 • Rev P • 09/28/15

Safety Alert Key:

•

DANGER!

Indicates a hazardous situation which, if not avoided will result in death or serious injury.

•

WARNING!

Indicates a hazardous situation which, if not avoided could result in death or serious injury.

•

CAUTION!

Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

•

NOTICE:

Indicates practices which may cause damage to the fireplace or to property.

Table of Contents

1 Product Specific & Important Safety Information

A. Fireplace Certification

B. Non-Combustible Materials

C. Combustible Materials

2 Getting Started

A. Typical Fireplace System

B. Design and Installation Considerations

1. Selecting Fireplace Locations

2. Locating Fireplace & Chimney

C. Tools and Supplies Needed

D. Inspect Fireplace and Components

E. Fireplace System Requirements

3 Framing and Clearances

A. Fireplace Dimensions

B. Clearances

Minimum Clearances to Combustibles

C. Construct the Chase

D. Frame the Fireplace

E. Secure and Level the Fireplace

F. Protective Metal Hearth Strips

G. Outside Air Kit

4 Chimney and Termination Requirements

A. Chimney Requirements

B. Offsets/Returns

C. Termination Requirements

5 Chimney Installation

A. Typical Chimney System

B. Assemble Chimney Sections

C. Intall Chimney Air Kit

D. Secure Offset/Return

E. Install Ceiling Firestops

F. Install Attic Insulation Shield

G. Roof Penetration

H. Install Chase/Chase Top

I. Termination Cap Requirements

J. Install Termination Cap

6 Shrouds

A. Radiation Shield

B. Field Constructed Shrouds

1. Open Top Shroud

2. Mailbox Style Shroud

3. Roofed Style Shroud

7 Finishing

A. Finishing Material

B. Hearth Extension, Building and Finishing

1. Fireplace Installed Flush on the Floor and

Hearth Extension Raised to Bottom of Firebox

Opening

2. Raised Hearth Extension and Raised Fireplace

3. Fireplace Opening and Hearth Extension Flush

with the Floor

C. Non-Combustible Sealant Material

D. Sidewalls/Surrounds

E. Mantel and Wall Projections

8 Fireplace Setup

A. Install Hearth Molded Brick Panel

B. Install Back Molded Brick Panel

C. Install Side Molded Brick Panel

D. Install Screens

E. Install Mortar (Optional)

F. Grate

I. Gas Log/Lighter Provision

J. Wood Burning Inserts

9 Reference Materials

A. Chimney Components

B. Optional Components

Note:

An arrow found in the text signifies change in content.

►

Содержание BIR42-B













































Результаты поиска

Содержание BIR42-B

Отзывы:

Похожие инструкции для BIR42-B

Бренды по названию

Популярные бренды

Heatilator BIR42-B, Руководство по установке

Результаты поиска

Содержание BIR42-B

Отзывы:

Похожие инструкции для BIR42-B

Бренды по названию

Популярные бренды