Heatilator Aveo ADVR3428 Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 78

Heatilator Aveo ADVR3428 Скачать руководство пользователя страница 58

Heatilator • AVEO Series DV • 4058-210 Rev P • 1/13

58

Replacing Fixed Glass Assembly

• Set the glass panel on the lower two glass assembly

latches, ensuring the glass panel is centered in the
opening.

• Push top in, fasten top two glass latches.
• Replace

screen.

O. Close the Screen Assembly

Rotate the screen closed. See Figures 15.12 and 15.13.

Figure 15.12 Closing Screen

Figure 15.13 Closing Screen

P. Air Shutter Setting

This appliance has an adjustable air shutter (which
controls the primary air) that can be accessed under the
valve compartment located under the fi rebox assembly
(Figure 15.14). The air shutter is factory set for the mini-
mum vertical vent run. If your installation has more than
the minimum required vertical vent length, adjustment of
the air shutter may be necessary to obtain optimal fl ame
appearance.

This should be adjusted by a qualifi ed

installer at the time of installation.

In the event of soot accumulation inside your appliance,
the air shutter should be opened further. When the shutter
adjustment handle is all the way

down

, the air shutter is

in the open position. When the shutter adjustment handle
is all the way

up

, the air shutter is in the fully closed posi-

tion.

Air Shutter

Thumb Screw

Figure 15.14 Air Shutter

Note:

Do not force thumb screw - air shutter slide could

be damaged!

«
...
56
57
58
59
60
...
»

Содержание Aveo ADVR3428















































































Отзывы:

Нет отзывов