manualshive.com logo in svg

Heatilator Aveo ADVR3428, Руководство пользователя по установке и эксплуатации, Страница: 41 / 78

Поделиться
Скачать
Heatilator Aveo ADVR3428 Скачать руководство пользователя страница 41

Heatilator  •  AVEO Series DV  •  4058-210 Rev P  •  1/13

41

Figure 10.8  Securing Vertical Pipe Sections

Figure 10.9  Securing Horizontal Pipe Sections

E. Disassemble Vent Sections

•  Rotate either section (see Figure 10.10) so the 

seams on both pipe sections are aligned as shown in 
Figure 10.11. 

•  Pull carefully to separate the pieces of pipe.

D. Secure the Vent Sections

•    Vertical runs originating off the top of the appliance, with 

no offsets, must be supported every 8 ft. (2.44 m) after 
the maximum allowed 25 ft. (7.62 m) of unsupported rise.

•    Vertical runs originating off the rear of the appliance, or 

after any elbow, must be supported every 8 ft. (2.44 m). 

•    Horizontal runs must be supported every 5 feet (1.52 m).

•  Wall shield fi restops may be used to provide horizontal 

support.

•   Vent support or plumber’s strap (spaced 120° apart)  

may be used for support. See Figures 10.8 and 10.9.

•  SLP ceiling fi restops have tabs that may be used to 

provide vertical support.

 

WARNING! Risk of Fire, Explosion or Asphyxi-
ation! 

Improper support may allow vent to sag and 

separate. Use vent run supports and connect vent 
sections per installation instructions. DO NOT allow 
vent to sag below connection point to appliance. 

Figure 10.11   Align and Disassemble Vent Sections

Figure 10.10  Rotate Seams for Disassembly

Содержание Aveo ADVR3428















































































Отзывы:

Нет отзывов