manualshive.com logo in svg

Heatilator Aveo ADVR3428, Руководство пользователя по установке и эксплуатации, Страница: 57 / 78

Поделиться
Скачать
Heatilator Aveo ADVR3428 Скачать руководство пользователя страница 57

Heatilator  •  AVEO Series DV  •  4058-210 Rev P  •  1/13

57

L. Install Hood

•  Locate the three screws just inside the upper section of 

the appliance.

•  Slide the hood into position under the screw heads.
•  Tighten the three screws. See Figure 15.9.

K. Unpackage the Hood & Floor Cover

Remove the hood, fl oor cover and protective cardboard 
from the back side of the screen as shown in Figure 15.8.

Figure 15.8  Removing Parts Package

Figure 15.9  Installing Hood

Latches

(both bottom 

and top)

Glass 

Assembly

Figure 15.11 Glass Assembly

M. Install Floor Cover

Install the fl oor cover as shown in Figure 15.10.

N. Fixed Glass Assembly

Removing Fixed Glass Assembly

WARNING! Risk of Asphyxiation! 

Handle fi xed glass 

assembly with care. Inspect the gasket to ensure it is 
undamaged and inspect the glass for cracks, chips or 
scratches.

DO NOT:

•  Strike, slam or scratch glass

• Operate fi replace with glass removed, cracked, 

broken or scratched.

Replace fi xed glass assembly as a complete assembly.

• Remove 

screen.

•  Pull the four glass assembly latches out of the groove 

on the glass frame. Refer to Figure 15.11.

•  Remove the glass assembly from the appliance.

Figure 15.10 Installing Floor Cover

Note: 

The fl oor cover in the bottom front of the fi replace 

may be covering the UL labels. It is loose and can be 
removed/replaced.

Содержание Aveo ADVR3428















































































Отзывы:

Нет отзывов