manualshive.com logo in svg

Heatilator Aveo ADVR3428, Руководство пользователя по установке и эксплуатации, Страница: 55 / 78

Поделиться
Скачать
Heatilator Aveo ADVR3428 Скачать руководство пользователя страница 55

Heatilator  •  AVEO Series DV  •  4058-210 Rev P  •  1/13

55

15 

15 

Appliance Setup 

 

A. Remove the Packaging

Remove the shrink fi lm, corrugated top cap, bottom cap 
and column protectors from the appliance. The appliance 
should look as shown in Figure 15.1.

B. Open Front Screen Assembly 

• Open 

the 

fl ap in the upper left hand corner of the screen 

protector (Figure 15.2)

•  Pick up on the screen to release the screen from 

the shoulder screws in the fireplace columns. See 
Figure 15.3.

•  Rotate the screen open as shown in Figure 15.4.

C. Remove the Shipping Materials

Remove the shipping materials from inside or underneath 
the fi rebox.

D. Remove Fixed Glass Assembly

See Section 15.N.

E. Clean the Appliance

Clean/vacuum any sawdust that may have accumulated 
inside the fi rebox or underneath in the control cavity.

Figure 15.1 Appliance Unwrapped

Figure 15.2  Open Access Flap

F. Accessories

Install approved accessories per instructions included 
with the accessories. Contact your dealer for a list of ap-
proved accessories.

WARNING! Rick of Fire and Electric Shock! 

Use ONLY 

Hearth & Home Technologies-approved optional acces-
sories with this appliance. Using non-listed accessories 
could result in a safety hazard and will void the warranty.

Figure 15.3  Lift up on Screen

Figure 15.4  Rotate Screen Open

Содержание Aveo ADVR3428















































































Отзывы:

Нет отзывов