Heatcraft Refrigeration Products BEACON II H-IM-79E Скачать руководство пользователя | Manualshive

Страница: 19 / 36

background image

19

Error Indicator

Air Defrost fan motors must be wired through the fan
relay on the Beacon II board for this to be effective on Air
Defrost systems. The entire system will be shut off and
remain off until the SPST switch is opened.

Air Defrost evaporator fans are setup to run constantly.
If there is a need to shut down the evaporator fans on
an Air Defrost system, this can be accomplished by
wiring the evaporator fan motor or evaporator fan motor
contactor through the fan relay on the Beacon II board.
When this is done and the Air Defrost system
is placed in “

SERVICE

,” the evaporator fans

will shut off when the system is in pumpdown.

ERROR CODES

  E1 -  Room temperature sensor shorted,
      open or not installed
  E2 -  Defrost temperature sensor shorted,
      open or not installed
  E3 -  Suction temperature sensor shorted,
      open or not installed
  E4 -  Suction pressure transducer shorted,
      open or not installed
  E5 -  Outdoor temperature sensor shorted
  E6 -  Low superheat
  E7 -  Compressor shut down
      (high or low pressure switch open or
      oil pressure switch open)
  E9 -  Multi-in/multi-out wiring error

Error Indicator Led

At initial power up, each Beacon II board checks for
system errors. The system error check involves checking
the various temperature sensors to determine whether
any of these sensors are shorted or open.

The system will pumpdown and cycle off and

will not

restart

until the fault is cleared or the circuit breaker

reset, for the following conditions:

-

Suction sensor shorted, open

or not installed

- Room temperature sensor shorted

or not installed

- Pressure Transducer open

or not installed

The system will pumpdown, cycle off and

try to restart

for these faults

. Each try will be after the 4 minutes

“Hold Off” period, for the following fault conditions:

- High pressure or low pressure cutout

- Oil pressure

After the fourth try, the Alarm contacts will be closed
and an alarm message displayed on the LED. To clear
this condition, the system should be cycled through the

“SERVICE MODE”

after the correction is completed.

Evaporator Fans Shut Off

In some installations, it is desirable to shut off the
evaporator fans periodically. This is easily accomplished
on Beacon II by wiring a single pole, single throw switch
(SPST) between the terminals marked “

SERVICE

” and

“

COM

” on the Beacon II board. Closing this switch will

cause the system to pumpdown and shut off.

«
...
17
18
19
20
21
...
»

Содержание BEACON II H-IM-79E





































Отзывы:

Нет отзывов

Похожие инструкции для BEACON II H-IM-79E

Бренд: GE Страницы: 2

Бренд: GE Страницы: 1

Бренд: GE Страницы: 2

Бренд: GE Страницы: 2

Бренд: GE Страницы: 1

Бренд: GE Страницы: 2

Бренд: GE Страницы: 36

Бренд: GE Страницы: 2

Бренд: GE Страницы: 2

Бренд: GE Страницы: 1

Бренд: GE Страницы: 2

Бренд: GE Страницы: 1

Бренд: GE Страницы: 20

Бренд: GE Страницы: 6

Spacemaker GMR04AAMWW

Бренд: GE Страницы: 2

Бренд: GE Страницы: 1

Бренд: GE Страницы: 1

Бренд: GE Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды