Heatcraft Refrigeration Products BEACON II H-IM-79E Скачать руководство пользователя

Страница: 14 / 36

Programming & Reviewing

FORCE

DEFROST

RESET

TIME

MONITOR

FORCE

SERVICE

Use the “MONITOR”

button to review these items:

SUP

- Superheat

(°F/°C)

ESP

- Expansion valve steps

(0 to 255 steps)

SCt

- Suction temperature

(°F/°C)

SSt

- Saturated Suction temperature

(°F/°C)

SCP

- Suction pressure at Evaporator

(PSIG/HG)

Odt

- Outdoor temperature

(°F/°C)

dFt

- Defrost sensor temperature

(°F/°C)

dFS

- Time left until next defrost

(hours) (on version 1.8 boards)

dFE

- Last Defrost Elapsed time

(minutes)

- Board Voltage

SPt

- Spare Temperature reading

Use this button to

“FORCE DEFROST”

To force a

defrost , press the

“FORCE DEFROST”

button. The

system will pumpdown and shut off the compressor. The
heaters are then turned on. The display will show

“dEF”

and room temp.

Use this button to

“RESET TIME”

Pressing this button

will reset the time clock in the microprocessor to zero.
At initial power up, pressing this button will bypass
the “four minute” hold-off and the system will start
immediately after the expansion valve opens. This
display will show

“dLy”

Use this button to

“FORCE SERVICE”

Pressing this button TWICE will cause the system to
pumpdown and the compressor to shut off. The system
will remain off until the “

CLEAR

” button is pressed.

While in the “

FORCE SERVICE

”, the LED display will

only show

“SEr”

Содержание BEACON II H-IM-79E





































Результаты поиска

Содержание BEACON II H-IM-79E

Отзывы:

Похожие инструкции для BEACON II H-IM-79E

Бренды по названию

Популярные бренды

Heatcraft Refrigeration Products BEACON II H-IM-79E, Инструкция по установке и эксплуатации

Результаты поиска

Содержание BEACON II H-IM-79E

Отзывы:

Похожие инструкции для BEACON II H-IM-79E

Бренды по названию

Популярные бренды