heatco EMA Series Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 33

heatco EMA Series Скачать руководство пользователя страница 7

7

Application Guidelines

Parallel installations are acceptable with all configurations.

Heaters may be installed in series

when applicable

(Limited to Two (2) in series).

Note that higher air

side pressure drop is expected when installing high efficiency (90%+) in series.

IV. Duct Installation

Duct work should be sized to fit flanged opening on the duct furnace. Ductwork should be mechanically fastened
to  heating  unit.  Joints  should  be  sealed  with  high  temperature  silicone  caulking  or  high  temperature  tape  to
prevent  leakage  of  circulating  air.  All  duct  connections  MUST  be  weather  tight  to  prevent  rain  and  snow  from
entering  ductwork.  Support  all  ductwork  securely.  DO  NOT  rely  solely  on  heating  unit  duct  connections  for
support.

Provide removable access panels in ductwork immediately upstream and downstream of duct furnace to allow for
inspection of the heat exchanger. These openings should be large enough to observe smoke or reflected light
inside the casing to inspect heat exchanger for leaks, and to check for hot spots on the heat exchanger due to
poor air distribution or insufficient air volume. Attach covers so as to prevent air leakage. See Figure 3.

WARNING !

Be sure the furnace/airflow configuration selected is appropriate for application

based on entering air temperature. Failure to install unit with proper airflow

direction may result in property damage, personal injury or death.

Duct

Furnace

Duct

Furnace

Airflow

Top View

OK

«
...
5
6
7
8
9
...
»

Содержание EMA Series


































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды