Heat-N-Glo 6000TRS-AU Скачать руководство пользователя страница 31

33

LIMITED 10 YEAR WARRANTY

HEAT-N-GLO, a division of Hearth Technologies Inc.

In order to presumptively establish the dates to which your HEAT-N-GLO Limited 10 Year Warranty runs, you must
mail the completed warranty card to HEAT-N-GLO, a division of Hearth Technologies Inc., 20802 Kensington
Boulevard, Lakeville, MN 55044, within 60 days of the date of fireplace installation.  If you fail to do so, you may
be required to prove the date of installation before warranty work can be performed.

The warranty exclusions and limitations of liability are effective upon installation of the fireplace.

Subject to the conditions set forth herein, HEAT-N-GLO, a division of Hearth Technologies Inc. ("HEAT-N-GLO")
extends the following warranty with respect to HEAT-N-GLO, a division of Hearth Technologies Inc..

If HEAT-N-GLO  is reasonably satisfied that any part or portion of the fireplace covered by this Limited Warranty
is defective in material or workmanship under normal use and service as described in the Operating Instructions,
HEAT-N-GLO will take the following actions:

1. If the defect is reported during the first year from the date of installation (stainless steel burners and fiber logs

are covered for 3 years), HEAT-N-GLO will replace or repair the defective components at its sole expense.  The
decision whether to replace a component shall be made at HEAT-N-GLO's sole discretion.  This Limited
Warranty does not cover components broken during shipping, misuse or careless handling.   HEAT-N-GLO shall
be not responsible for any indirect, incidental, or consequential damages or for any costs other than those
incurred by HEAT-N-GLO to repair or replace the defective component.  If components (including venting) other
than factory approved components are used, all warranty and liability on the fireplace is voided.

Defects

reported after the first year will not be covered by warranty unless they fall within the purview of
paragraph 2 or 3 below.

2. If the following defects are reported during the second year after the date of installation, HEAT-N-GLO will supply

replacement parts at the current wholesale price: defective electrical or manual components, optional
components or accessories, and glass panels (not including glass panels broken during misuse or careless
handling).  HEAT-N-GLO shall not be responsible for any labor, transportation or other costs.  Furthermore, it
shall not be liable for any indirect, incidental or consequential damages.

3. HEAT-N-GLO will replace or repair a defective firebox or heat exchanger, at any time during the 10 years from

the date of installation. The decision whether to replace the defective component shall be made at HEAT-N-
GLO's sole discretion. HEAT-N-GLO shall not be responsible for any indirect, incidental or consequential
damages or for any costs other than those incurred by HEAT-N-GLO to repair or replace the defective
component.

This Limited Warranty is the exclusive remedy available to you.  If HEAT-N-GLO cannot effectively resolve a
warranty problem in an expedient and cost-effective manner, it can discharge its entire warranty liability by refunding
the price of the product to you.

Products made by other manufacturers, whether sold with the fireplace or added thereafter, are NOT covered by
this Limited Warranty.  The use of other unauthorized components will make this warranty null and void.  This Limited
Warranty will also be void if the appliance is not installed by a qualified installer in accordance with the Installation
Instructions.  Furthermore, the Limited Warranty will be  void if the fireplace is not operated, at all times, according
to the Operating Instructions furnished with the fireplace. Any service work must be performed by authorized service
representatives.

EXCEPT TO THE EXTENT PROVIDED BY LAW, NO OTHER EXPRESS OR IMPLIED WARRANTIES,
INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, SHALL
APPLY TO THE FIREPLACE PRODUCT.  In States that do not allow limitations on how long an implied warranty
lasts, or do not allow exclusion of indirect damages, those limitations or exclusions may not apply to you.  You may
also have additional rights not covered in this Limited Warranty.

HEAT-N-GLO reserves the right to make changes at any time, without notice, in design, material, specifications
and prices.  It also reserves the right to discontinue styles and products.

Содержание 6000TRS-AU
































Отзывы: