HEAT GLO PROV-I30-IPI Скачать руководство пользователя страница 31

Страница: 31 / 47

Heat & Glo • SUPREME-I25-IFT, SUPREME-I30-IFT, SUPREME-I35-IFT Installation Manual • 2532-980 Rev. E • 5/19

A. Fuel Conversion

• Make sure the appliance is compatible with available gas

types.

• Conversions must be made by a qualified service

technician using Hearth & Home Technologies specified

and approved parts.

• Reference the following diagrams for gas shut off detail

and component access.

• Reference Section 9.A to remove fixed glass assembly.

Gas Information

Figure 7.2

Glass Clip Assembly Removal

BASE REFRACTORY

GLASS CLIP

ASSEMBLIES

GLASS

CLIP ASSEMBY

SCREW ACCESS

Figure 7.1 Gas Shut-off

Figure 7.3 Component Tray

• Glass clip assemblies can be removed for additional

component accessibility.

• Use multi-purpose tool to assist with gas shutoff. See

Figure 7.1. The gas ball valve is in the “OFF” position

from manufacturer.

WARNING!

Glass seal plate must be properly installed.

Risk of elevated component temps and carbon monoxide

exposure.

NOTE:

Bottom right glass clip on 25 inch models must

be removed to gain access to controls.

OFF POSITION

(TURN KNOB CLOCKWISE)

NOTE: Use the Multi-Purpose

Tool to assist with gas shut-off.

MULTI-PURPOSE TOOL

GAS SHUT OFF

GLASS SEAL PLATE

COMPONENT TRAY

WITH HEAT SHIELD

PRESS

TAB TO

RELEASE

UNCLIP

WIRES

COMPONENT

TRAY

COMPONENT

TRAY RECEIVER

CAUTION:

Be sure to reinstall the component heat shield

before firing the appliance. Components will overheat.

NOTE: The gas ball

valve is in the “OFF

position from

manufacturer.

Содержание PROV-I30-IPI
















































Результаты поиска

Содержание PROV-I30-IPI

Отзывы:

Бренды по названию

Популярные бренды

HEAT GLO PROV-I30-IPI, Руководство по установке

Результаты поиска

Содержание PROV-I30-IPI

Отзывы:

Бренды по названию

Популярные бренды