Hearth & Home PVLP-SLP-AU Скачать руководство пользователя страница 19

Страница: 19 / 22

Hearth & Home Technologies • Power Vent Low Profile (PVLP-SLP-AU) Instructions • 4052-902 Rev. C • 10/19

A. Installation Inspection

1. Follow safety inspection procedures recommended by

national, provincial, and/or local codes.

2. Be certain all electrical connections are properly made

and secure.

3. Visually inspect the vent system and determine that

there is no flue gas spillage, blockage or restriction,

leakage, corrosion or other unsafe deficiencies.

4. Check timings set on time on and time off delay relays.
Time on Delay: 100-120 sec

This can be measured by taking the time from when

the wall switch is turned on until the time at which

the module beeps.

Time off Delay: 18-22 minutes

This can be measured by taking the time from when

the wall switch is turned off until the time when the

fan turns off.

Operating Instructions

CAUTION! Risk of electrical shock! DO NOT

allow

240VAC

wires to contact hot metal surfaces. Use sup-

plied wire ties to bundle wires away from flue pipe, fan

housing and other metal surfaces.

B. Power Vent Operating Instructions

After installation of the power vent, follow the operation

instructions below.

IPI Plus/RC300

1. Turn the wall switch "ON".

NOTE

: A 100-120 second pre-purge will begin. Once this

is complete, power is supplied to the appliance. This can

be verified by a beep sound from the module.
2. Turn the remote "ON".

NOTE

: After turning the remote to the "ON" position, if the

appliance does not turn on, turn the remote to "OFF" refer

to the troubleshooting section.
3. Turn the remote to "OFF" to turn off the burner. Turn

the wall switch to "OFF" to turn off the power vent.

NOTE:

The power vent will continue to run for 20 minutes.

To operate the power vent and fireplace appliance with only

the wall switch, connect the red and brown wires together

coming from the control module wiring harness, see Figure

5.1. This will automatically start the fireplace appliance

after the pre-purge is complete. Allow customer to set

desired flame height and fan setting on remote before red

and brown wires are jumped together.

8K1 WIRE

HARNESS

GROUND

CONTROL MODULE

CONNECT RED

AND BROWN

WIRES TOGETHER

RED

BROWN

Figure 5.1

NOTE:

If relays are set incorrectly refer to section 4.C.

for the correct relay settings.

Содержание PVLP-SLP-AU























Результаты поиска

Содержание PVLP-SLP-AU

Отзывы:

Бренды по названию

Популярные бренды

Hearth & Home PVLP-SLP-AU, Руководство по установке

Результаты поиска

Содержание PVLP-SLP-AU

Отзывы:

Бренды по названию

Популярные бренды