Hearth & Home IntelliFire IFT-RC150 Скачать руководство пользователя страница 9

9

Hearth & Home Technologies  •  RC150 IntelliFire

 Touch Installation Instructions  •  2326-980  •  9/16

Please contact your Hearth & Home Technologies 

dealer with any questions or concerns. 

For the location of your nearest 

Hearth & Home Technologies dealer, 

please visit www.hearthnhome.com.

Hearth & Home Technologies  

7571 215th Street West, Lakeville, MN 55044

www.hearthnhome.com

FCC Compliance Statement:

This device complies with part 15 of the FCC Rules. Op-

eration is subject to the following two conditions: 

(1) This device may not cause harmful interference, and 
(2) This device must accept any interference received, in-

cluding interference that may cause undesired opera-

tion of the device. 

FCC Warning

Note: 

This equipment has been tested and found to 

comply with the limits for a Class B digital device, pur-

suant to Part 15 of the FCC Rules. These limits are de-

signed to provide reasonable protection against harmful 

interference in a residential installation. This equipment 

generates, uses, and can radiate radio frequency en-

ergy and, if not installed and used in accordance with 

the instructions, may cause harmful interference to radio 

communications. However, there is no guarantee that in-

terference will not occur in a particular installation. If this 

equipment does cause harmful interference to radio or 

television reception, which can be determined by turning 

the equipment off and on, the user is encouraged to try to 

correct the interference by one or more of the following 

measures:
•  Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and 

receiver.

•  Connect the equipment into an outlet on a circuit different 

from that to which the receiver is connected.

Canadian DOC Notice

This digital apparatus does not exceed the (Class A/ 

Class B) limits for radio noise emissions from digital ap-

paratus set out in the Radio Interference Regulations of 

the Canadian Department of Communications. 

Canadian IC Notice

This device complies with RSS-210 of Industry and Sci-

ence  Canada.  Operation  is  subject  to  the  following  two 

conditions: (1) this device may not cause interference, and 

(2) this device must accept any interference, including in-

terference that may cause undesired operation of the de-

vice.

Caution: 

The Federal Communications Commission 

warns  that  changes  or  modifications  not  expressly  ap

-

proved by the party responsible for compliance could void 

the user’s authority to operate the equipment. 

•  Consult the dealer or an experienced radio/TV technician 

for help.

Содержание IntelliFire IFT-RC150










Отзывы: