background image

7

Hearth & Home Technologies  • SMART-BATT-II Remote Control Instructions  •  100-909 Rev. i  •  5/12

NOTE:

 The remote receiver houses the microprocessor 

that responds to commands from the transmitter to control 
system operation. It emits one beep when it receives an 
ON or OFF command manually, but no beep when cycling 
on and off automatically in THERMO mode.

The remote receiver has a 3-position slide switch: OFF/
REMOTE/ON (see Figure 11).

Figure 11.  Remote Receiver Slide Switch

NOTE: The remote receiver will only respond to the 
transmitter when the 3-position slide button on the 
remote receiver is in the Remote position. If the system 
does not respond to the transmitter on initial use, see 
section Matching Security Codes.

1.  With the slide switch in the ON position, the system is on.

2. With the slide switch in the REMOTE position, the system 

only operates if the remote receiver receives commands 
from the transmitter.

3. With the slide switch in the OFF position, the system is off.

NOTE:

 The slide switch should be placed in the OFF posi-

tion if you will be away from your home for an extended 
period of time. Placing the switch in the OFF position also 
functions as a safety “lock out” by turning the system off 
and rendering the remote receiver inoperative.

TRANSMITTER

Important: Before operating remote control, transmitter 
and receiver must have matching security codes. See 
section ‘Matching Security Codes’.

Important:

 Review ‘Thermo-Safety/Communication-Safety 

Features’ under ‘Transmitter Safety Features’ section. 
These signal/temperature safety features shut down the 
fi replace system when a potentially unsafe condition ex-
ists. 

Important: 

Review ‘Auto Shutdown’ section. This safety 

feature shuts down the fi replace after 9 hours of continuous 
operation, in ON mode only.

Important:

 New batteries are essential for proper operation 

of the multi-function transmitter. The transmitter operates 
on 2 AAA-size 1.5V batteries. Use Alkaline batteries for lon-
ger battery life and maximum operational performance.

Insert 2 AAA-size 1.5V batteries into the battery compart-
ment on the back of the transmitter. When the batteries 
are correctly inserted, the screen will display numbers (see 
Figure 7 for LCD Display Screen).

NOTE:

 If the transmitter is activated from a very cold 

condition it may be necessary to allow the transmitter to 
stabilize to room temperature (could take up to 15 minutes) 
before accurate room temperatures are displayed on the 
screen. 

NOTE: 

LCD screen is equipped with a “backlite” for easier 

viewing of LCD screen. Backlite illuminates when a function 
button is depressed. After 5 seconds elapses, LCD screen 
will return to its normal state.

BATTERY

COVER

WIRE

TERMINALS

ON/OFF REMOTE SLIDE SWITCH

LEARNING BUTTON

Содержание SMART-BATT-II













Отзывы: