HCC Technology POS80B Скачать руководство пользователя страница 52

Страница: 52 / 71

Thermal Printer Technical Manual

FS ! or GS ! can also select and cancel quadruple-size mode by selecting double-height and
double-width modes, and the setting of the last received command is effective.

[Default]

n = 0

[Reference]

FS !, GS !

GS H n Select printing position for HRI characters

[Name]

Select printing position for HRI characters

[Format]

ASCII

Hex

Decimal

[Range]

0 ≤ n ≤ 3, 48 ≤ n ≤ 51

[Description]

Select the printing position of HRI characters when printing a bar code.n selects the printing
position as follows:

Printing position

0, 48

Not printed

1, 49

Above the bar code

2, 50

Below the bar code

3, 51

Both above and below the bar code

HRI indicates Human Readable Interpretation.

[Notes]

HRI characters are printed using the font specified by GS f.

[Default]

n = 0

[Reference]

GS f, GS k

GS f n Select font for Human Readable Interpretation (HRI) characters

[Name]

Select font for Human Readable Interpretation (HRI) characters

[Format]

ASCII

Hex

Decimal

102

[Range]

n = 0, 1, 48, 49

[Description]

Select a font for the HRI characters used when printing a bar code. n selects a font from the
following table:

Font

0, 48

Standard ASCII characters (12 × 24)

1, 49

Compressed ASCII characters (9 × 17)

[Notes]

HRI indicates Human Readable Interpretation.
HRI characters are printed at the position specified by GS H.

[Default]

n = 0

[Reference]

GS H, GS k

Содержание POS80B








































































Результаты поиска

Содержание POS80B

Отзывы:

HCC Technology POS80B, Техническое руководство, Страница: 52 / 71

Результаты поиска

Содержание POS80B

Отзывы: