HCC Technology POS80B Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 71

HCC Technology POS80B Скачать руководство пользователя страница 33

Thermal Printer Technical Manual

33

[Reference]

GS /

GS / m Print downloaded bit image

[Name]

Print downloaded bit image

[Format]

ASCII

GS

/

m

Hex

1D

2F

m

Decimal

29

47

m

[Range]

0 ≤ m ≤ 3, 48 ≤ m ≤ 51

[Description]

Print a downloaded bit image using the mode specified by m. m selects a mode from the table
below:

[Notes]

This command is ignored if a downloaded bit image has not been defined.
In standard mode, this command is effective only when there is no data in the print buffer.
This command has no effect in the print modes (emphasized, double-strike,underline, character
size, or white/black reverse printing), except for upside down printing mode.
If the downloaded bit-image to be printed exceeds the printable area, the excess data is not
printed.
The command to print bitmap downloaded into RAM bitmap is not downloaded to the FLASH
bitmap.

[Reference]

GS

*

FS P n Print NV bit image

[Name]

Print NV bit image

[Format]

ASCII

FS

P

n

Hex

1C

50

n

Decimal

28

80

n

[Range]

0 ≤ n ≤ 7

m

Mode

Vertical Dot Density (DPI)

Horizontal Dot Density (DPI)

0, 48

Normal

203

203

1, 49

Double-width

203

101

2, 50

Double-height

101

203

3, 51

Quadruple

101

101

«
...
31
32
33
34
35
...
»

Содержание POS80B








































































Отзывы:

Нет отзывов