HCC Technology POS80B Скачать руководство пользователя страница 43

Страница: 43 / 71

Thermal Printer Technical Manual

•

Contents stored in the NV user memory.

•

Contents defined for the NV graphics (NV bit image).

•

Maintenance counter value.

•

Setting values specified with the customized values (memory switches), GS ( E.

ESC p m t1 t2 Generate pulse

[Name]

Generate pulse

[Format]

ASCII

ESC p

m t1

Hex

m t1

Decimal

112

m t1

[Range]

m = 0, 1, 48, 49

0 ≤ t1 ≤ 255, 0 ≤ t2 ≤ 255

[Description]

Output the pulse specified by t1 and t2 to connector pin m as follows:

[Notes]

The pulse ON time is [ t1 × 2 ms] and the OFF time is [ t2 × 2 ms].
If t2 < t1, the OFF time is [ t1 × 2 ms]

[Reference]

DLE DC4

GS I n Check printer ID

[Name]

Check printer ID

[Format]

ASCII

Hex

49 n

Decimal

73 n

[Range]

1 ≤ n ≤ 3, 49 ≤ n ≤ 51, 65 ≤ n ≤ 69

[Description]

Check printer ID specified by n as follows:

Printer ID

ID (hexadecimal)

1, 49

Printer model ID

printer models related

2, 50

Type ID

See table below.

3, 51

ROM version ID

printer model and batch related

Firmware version

printer model and batch related

Manufacturer

the actual manufacturer related

Printer name

the actual printer name related

Serial number

printer model and batch related

Supporting

Chinese

type

Simplified Chinese

：

Chinese

Traditional Chinese

：

Chinese-BIG5

n = 2, Type ID

Bit

1/0

Hex

Decimal

Function

Two-byte character code not supported.

Two-byte character code supported.

Auto-cutter not equipped.

Auto-cutter equipped.

Not used.

Connector pin

0, 48

Drawer kick-out connector pin 2.

1, 49

Drawer kick-out connector pin 5.

Содержание POS80B








































































Результаты поиска

Содержание POS80B

Отзывы:

HCC Technology POS80B, Техническое руководство, Страница: 43 / 71

Результаты поиска

Содержание POS80B

Отзывы: