9
Use Only Genuine Hayward Replacement Parts.
Operating the Viio Turbo Cleaner
9
W
Wa
arrn
niin
ng
g -- R
Riissk
k o
off IIn
njju
urryy
The Filtration and Booster Pumps must be
O
OF
FF
F
when connecting
or disconnecting cleaner hose.
C
Ca
au
uttiio
on
n -- R
Riissk
k o
off E
Eq
qu
uiip
pm
me
en
ntt D
Da
am
ma
ag
ge
e
The filter pump must always be run to clear air from the system
before turning the Booster Pump
O
ON
N.. N
Ne
ev
ve
err rru
un
n
the Booster
Pump without the main filter pump
O
ON
N
. Running the Booster
Pump dry will damage the Booster Pump and void the warranty.
O
Op
pe
erra
attiin
ng
g tth
he
e V
Viiiio
o T
Tu
urrb
bo
o C
Clle
ea
an
ne
err
1
1..
Be sure all filtration system valves are open and supplying
water to the Booster Pump.
2
2..
Be sure valves to and from the Booster Pump and dedicated
return line are fully opened.
3
3..
The Viio Turbo Cleaner and its Booster Pump can only
operate when the pool’s filter pump is operating.
C
Ca
au
uttiio
on
n -- R
Riissk
k o
off E
Eq
qu
uiip
pm
me
en
ntt D
Da
am
ma
ag
ge
e
Failure to open valves fully and/or failure to have the filtration
system operating will damage the Booster Pump. This damage
voids the Booster Pump’s warranty.
S
Se
ettttiin
ng
g P
Prre
essssu
urre
e
IIm
mp
po
orrtta
an
ntt::
The cleaner will not operate properly if the pressure
is not properly set. Too little pressure will prevent proper
movement and cleaning. Too much pressure will cause poor
cleaning and premature wear of Cleaner parts.
W
Wa
arrn
niin
ng
g -- R
Riissk
k o
off IIn
njju
urryy
Be careful to hold the Cleaner Connector (Part C) with the Setup
Pressure Gauge (Part U) attached under water and not to be
sprayed by the hole in the Setup Pressure Gauge or by the
Sweep Hose.
N
Ne
ev
ve
err
point a jet or hose at people or pets.
Clip the Setup Pressure Gauge to the hose near the Wall Quick
Connect.
1
1..
Turn the filtration system pump
O
ON
N
then the Booster Pump
O
ON
N
. Read the pressure on the Setup Pressure Gauge
connected to the Cleaner Connector. Use a flat blade
screwdriver to adjust the Wall Quick Connect Knob
(see figure 2) until the pressure reads 25 PSI (
+
/- 5 PSI).
N
No
otte
e::
The Wall Quick Connect can be adjusted from “0”
(fully closed) to “5” (fully open). Do
N
NO
OT
T
force the
adjustment knob beyond “0” or “5”.
2
2..
If the Wall Connector is on Position “5” (fully open) and the
pressure is still below 20 PSI, check for clogged Filter, Pump
Strainer Basket, Main Drain, Skimmer Basket, etc., to
determine why there is insufficient water pressure at the
dedicated line. If more pressure is still required have an
Authorized Hayward Pool Dealer or Service person check
the Booster Pump, Filtration System and Plumbing to
determine if they are functioning correctly.
3
3..
Turn the Booster Pump and Filtration Pump
O
OF
FF
F
.
4
4..
R
Re
em
mo
ov
ve
e tth
he
e S
Se
ettu
up
p P
Prre
es
ss
su
urre
e G
Ga
au
ug
ge
e
from the Cleaner
Connector. Store the Setup Pressure Gauge with the
Owner’s Guide in a safe place.
5
5..
Attach the Cleaner Connector to Cleaner. The Sweep Hose
should be directly below the Pressure Hose.
6
6..
Place the cleaner in the pool, turn the Filtration system
O
ON
N
,
then turn the Booster Pump
O
ON
N
.
C
Co
on
nn
ne
ec
cttiin
ng
g P
Prre
es
ss
su
urre
e H
Ho
os
se
e tto
o C
Clle
ea
an
ne
err
A
Ad
djju
us
sttiin
ng
g P
Prre
es
ss
su
urre
e a
att W
Wa
allll C
Co
on
nn
ne
ec
ctto
orr
S
Se
ettu
up
p P
Prre
es
ss
su
urre
e G
Ga
au
ug
ge
e &
& W
Wa
allll C
Co
on
nn
ne
ec
ctt
K
C
U
C
Figure 1
Figure 2
Figure 3
