TriStar Pump Series Page 5 of 8
™
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
WARNING
-
Hazardous Pressure.
Pumps, filters, and other equipment/components of a swimming pool
filtration system operate under pressure. Incorrectly installed and/or improperly tested filtration equipment and/or components
may fail resulting in injury and/or property damage.
Pump Mounting (cont’d.)
Plumbing
Use Teflon tape to seal threaded connections on molded plastic components. All plastic fittings must be new or thoroughly cleaned before
use.
NOTE - Do NOT use Plumber’s Pipe Dope as it may cause cracking to the plastic components.
When applying Teflon tape to
plastic threads, wrap the entire threaded portion of the male fitting with one to two layers of tape. Wind the tape clockwise as you face the
open end of the fitting, beginning at the end of the fitting. The pump suction and outlet ports have molded-in thread stops. Do NOT attempt
to force hose connector fitting past this stop. It is only necessary to tighten fittings enough to prevent leakage. Tighten fitting by hand and
then use a tool to engage fitting an additional 1 ½ turns. Use care when using Teflon tape as friction is reduced considerable;
do NOT
over-tighten fitting or you may cause damage.
If leaks occur, remove connector, clean off old Teflon tape, re-wrap with one or two
additional layers of Teflon tape, and re-install connector.
Fittings
Fittings restrict flow. For better efficiency, use the fewest possible fittings (but at least two suction outlets). Avoid fittings that could cause
an air trap. Pool and spa fittings MUST conform to the International Association of Plumping and Mechanical Officials (IAPMO)
standards. Use a non-entrapping suction fitting in pool (multiple drains) or double suction (skimmer and main drain).
Electrical
WARNING
-
Ground and bond motor before connecting to electrical power supply. Failure to ground and
bond pump motor can cause serious or fatal electrical shock hazard.
WARNING
-
Do NOT ground to a gas supply line.
WARNING
-
To avoid dangerous or fatal electrical shock, turn OFF power to motor before working on
electrical connections.
WARNING
-
Ground Fault Circuit Interrupter (GFCI) tripping indicates electrical problem. If GFCI trips and
wont reset, consult electrician to inspect and repair electrical system.
WARNING
-
Fire Hazard.
Match supply voltage to motor nameplate voltage.
Insure that the electrical supply available agrees with the motor’s voltage, phase, and cycle, and that the wire size is adequate for the H.P.
(KW) rating and distance from the power source.
NOTE - All electrical wiring MUST be performed by a licensed electrician, and
MUST conform to local codes and Canadian Electrical Code regulations.
Use copper conductors only.
Motor Specifications
M otor B r ake H or sepower
M otor Rated H or sepower
M otor E lectr ic V /A
W ir e Size / B r eaker
H P (kW )
H P (kW )
V oltage
Amps
AW G
Amps
1.13 (0.84)
0.50 (0.37)
208 - 230 / 115
5.3 - 4.9 / 9.8
14
10 / 15
1.39 (1.04)
0.75 (0.56)
208 - 230 / 115
7.0 - 6.2 / 12.4
14
10 / 15
1.85 (1.38)
1.00 (0.75)
208 - 230 / 115
8.5 - 7.4 / 14.8
14 / 12
15 / 20
2.40 (1.79)
1.50 (1.12)
208 - 230 / 115
11.2 - 10.2 / 20.4
14 / 10
15 / 30
2.70 (2.01)
2.00 (1.49)
208 - 230
11.8 - 11.0
14
15
3.60 (2.69)
3.00 (2.24)
208 - 230
16.0 - 14.8
12
20
3.60 (2.69) *
3.00 (2.24) *
208 - 230 / 460 *
9.6 - 9.4 / 4.7 *
14 *
15 / 10 *
1.85 / 0.22 (1.38 / 0.16)
1.00 / 0.12 (0.75 / 0.09)
208 - 230
8.6 - 8.2 ¹
14
15
2.40 / 0.28 (1.79 / 0.21)
1.50 / 0.18 (1.12 / 0.13)
208 - 230
11.4 - 10.4 ²
14
15
Fu
ll
R
at
e P
um
ps
2.70 / 0.33 (2.01 / 0.25)
2.00 / 0.25 (1.49 / 0.19)
208 - 230
12.4 - 11.2 ³
14
15
0.94 (0.70)
0.75 (0.56)
5.4 / 10.8
14
10 / 15
1.25 (0.93)
1.00 (0.75)
230 / 115
7.0 / 14.0
14
10 / 15
1.65 (1.23)
1.50 (1.12)
230 / 115
7.7 / 15.4
14 / 12
10 / 20
2.20 (1.64)
2.00 (1.49)
230 / 115
10.8 / 21.6
14 / 10
15 / 30
2.60 (1.94)
2.50 (1.86)
230
11.5
14
15
3.45 (2.57)
3.00 (2.24)
230
13.5
14
15
1.85 / 0.22 (1.38 / 0.16)
1.50 / 0.18 (1.12 / 0.13)
208 - 230
8.6 - 8.2 ¹
14
15
2.40 / 0.28 (1.79 / 0.21)
2.00 / 0.25 (1.49 / 0.19)
208 - 230
11.4 - 10.4 ²
14
15
M
ax
R
at
e P
um
ps
2.70 / 0.33 (2.01 / 0.25)
2.50 / 0.31 (1.86 / 0.23)
208 - 230
12.4 - 11.2 ³
14
15
¹ ²
,
-
-
-
-
-
¹, ², ³ Low Speed Amps: (¹ 2.8 - 3.0) (² 3.2 - 3.4) (³ 3.8 - 4.1)
* Three-Phase (3Φ) Pump - motor starter required
