USE ONLY HAYWARD® GENUINE REPLACEMENT PARTS
4
Your Hayward Super II ECO Single Speed Pump is specifically engineered for the demanding requirements of today’s in-ground/above
ground swimming pool/spa that is equipped with large capacity filters, heaters, and pool cleaning equipment. The self-priming centrifugal
pump has been quality-built and engineered to give you many years of efficient, dependable, corrosion free service. The advanced design
reduces operation and maintenance to simple, commonsensical procedures.
Product Dimensions
All dimensions in millimeters
INSTALLATION
WARNING –
This product should be installed and serviced only by a qualified professional.
Pump Location
Locate the pump as practically close to the pool as possible. Run the suction line as directly as possible,
from pump to pool, in order to reduce friction losses. The suction line should have a continuous slope
upward from lowest point in line. Joints must be tight (but not over-tightened). The suction line must not
be smaller than 40 mm PVC and must be equal to or larger in diameter than the discharge line diameter.
Though the pump is designed for outdoor use, it is advised to place pump and filter in the shade to shield
them from continuous direct heat. Select a well-drained area that will not flood when it rains. Do NOT
install pump and filter in a damp or non-ventilated location. Keep motor clean. Pump motors require free
circulation of air for cooling. The maximum Suction Lift with out a check valve installed in the suction piping
where the pump can still prime is 1.8 metres.
Pump Mounting
Install pump on a level concrete slab or other rigid base to meet all local and national codes.
Secure pump to base with screws or bolts to further reduce vibration and stress on pipe joints.
The base must be level, rigid, and vibration free.
Pump mount must:
»
Allow pump inlet height to be as close to water level as possible.
»
Allow use of a short, direct suction pipe (to reduce friction losses).
»
Allow for valves in suction and discharge piping.
»
Be protected from excess moisture and flooding.
»
Allow adequate access for servicing the pump and piping.
*NOTE: It is recommended that a minimum length of straight piping (shown as “L” in diagram to the right), equivalent to 5 pipe size diameters,
be used between the pump suction inlet and any plumbing fittings (elbows, valves, ect).
INTRODUCTION
Top View
Side View
“
L
”
R
8.635
9.458
7.625
12.149
18.866
13.817
24.348
10.358
8.154
10.392
10.017
REVISIONS
REV. DESCRIPTION
DATE
FAI / NCMR
PCD / PLM
BY
APPD
D
C
B
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
E
F
E
F
A
SHEET 1 OF 1
2017/8/18
MODELED
WEIGHT:
COLOR:
2017/1/10
SCALE: 1:1
REV
DWG. NO.
E
SIZE
DESCRIPTION:
NAME
DATE
Q.A.
MFG APPR.
ENG APPR.
CHECKED
DRAWN
MATERIAL:
SEE PART DRAWINGS
UNAUTHORIZED USE, MANUFACTURE, OR REPRODUCTION IN WHOLE OR IN PART IS PROHIBITED. DRAWING, DESIGN, AND OTHER DISCLOSURES ARE PROPERTY OF: HAYWARD POOL PRODUCTS
74.44 LBS.
SEE PART DRAWINGS
STATUS:
R
8.635
9.458
7.625
12.149
18.866
13.817
24.348
10.358
8.154
10.392
10.017
REVISIONS
REV. DESCRIPTION
DATE
FAI / NCMR
PCD / PLM
BY
APPD
D
C
B
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
E
F
E
F
A
SHEET 1 OF 1
2017/8/18
MODELED
WEIGHT:
COLOR:
2017/1/10
SCALE: 1:1
REV
DWG. NO.
E
SIZE
DESCRIPTION:
NAME
DATE
Q.A.
MFG APPR.
ENG APPR.
CHECKED
DRAWN
MATERIAL:
SEE PART DRAWINGS
UNAUTHORIZED USE, MANUFACTURE, OR REPRODUCTION IN WHOLE OR IN PART IS PROHIBITED. DRAWING, DESIGN, AND OTHER DISCLOSURES ARE PROPERTY OF: HAYWARD POOL PRODUCTS
74.44 LBS.
SEE PART DRAWINGS
STATUS:
219
240
264
351
309
SIIE 320, 350 & 430 = 246
SIIE 350 & 430 = 594
SIIE 320 = 569
SIIE 530 & 580 = 263
SIIE 530 & 580 = 618
207
