Hayward Salt & Swim Скачать руководство пользователя

Страница: 17 / 24

Trrrrroubleshooting

oubleshooting

Visit www

www

www.haywar

.haywar

.hayward.com

d.com

d.com or call 855-429-9274

855-429-9274

855-429-9274 for helpful information on opera-

tion, maintenance and troubleshooting your Salt & Swim Electronic Chlorine Gen-

erator.

Common Problems and Solutions

The Salt & Swim's various LEDs show the operation status as well as alert the user

to any problems that may have occurred. Some indications may require a combi-

nation of LEDs to illuminate. To aid in interpreting these indications, Hayward has

created an interactive tool located at www.hayward.com. Use this tool and the

information below to identify and correct problems that may arise.

1. Possible causes of little or no free chlorine residual

Possible causes of little or no free chlorine residual

- DAILY CHLORINE OUTPUT adjustment setting is too low

- Low stabilizer (Cyanuric Acid)

- Filter pump time too short (8 hours for average size pools, more for large pools)

- Salt level too low (below 2400 ppm)

- Salt level too high

- Very warm pools increase chlorine demand--increase Output %, or filter run time

- Cold water below 50ºF causes Salt & Swim to stop generating

- Cold water between 50ºF - 60ºF causes Salt & Swim to reduce output regard-

less of DAILY CHLORINE OUTPUT setting

- Excessive scaling on Cell.

- High level of Nitrogen in pool water.

- "Yellow Out" or similar treatment recently used. Some yellow algae treatments

will use chlorine at a very high rate and deplete the residual free chlorine. Manu-

ally shock the pool if indicated in the directions on the algae treatment. It still

may be a matter of days before the pool returns to "normal" and chlorine tests

will show the desired 1-3ppm free chlorine reading.

2. LEDs not on

LEDs not on

Depending on current conditions, there should always be at least one LED illumi-

nated when the Salt & Swim is powered. If no LEDs are on, check to make sure

that the linecord is plugged in and that the GFCI outlet is powered. If no power is

detected, the GFCI may have to be reset.

3.....

STANDING BY LED blinking

ANDING BY LED blinking

The Salt & Swim has shut down because the temperature of the pool/spa water is

too high (120ºF) or too low (50ºF). The system will not resume operation until the

water temperature returns to normal. Note: This condition can sometimes happen

if the pool/spa temperature is already high and the heater is running. The tempera-

ture coming out of the heater and into the Cell could possibly be high enough to

shut down the Salt & Swim.

4. INADEQUA

INADEQUA

INADEQUATE W

TE W

TE WA

ATER FLOW LED illuminated

TER FLOW LED illuminated

The Salt & Swim has sensed a low flow or no flow condition and has stopped

generating chlorine.

- Verify that the filter pump is running and there are no obstructions or restrictions

in the pool plumbing.

- Backwash the pool filter.

- Increase the speed of your variable speed pump

Содержание Salt & Swim
























Результаты поиска

Содержание Salt & Swim

Отзывы:

Похожие инструкции для Salt & Swim

Бренды по названию

Популярные бренды

Hayward Salt & Swim, Руководство пользователя

Результаты поиска

Содержание Salt & Swim

Отзывы:

Похожие инструкции для Salt & Swim

Бренды по названию

Популярные бренды