Hayward H150FDN Скачать руководство пользователя

Страница: 55 / 65

Verify 22-28VAC off gas valve during ignition trial.

IF present & no pressure (manometer attached),

replace valve. Otherwise, replace ICB (

pg. 20

Verify correct flame sensor

Verify that the installed flame sensor is 5”. IF 3” is

installed OR IF sensor is damaged, replace it with

the 5” version (

pg. 20

). IF correct, go to step 12G.

Voltage/pressure off gas valve

Step 12E

Check for damaged/wrong blower air inlet plate. IF

wrong or damaged contact tech support (908) 355-

7995. IF OK, go to step 12H.

Verify blower air inlet plate

Step 12G

Inspect Gas Orifices & Burners for blockage. Clean

as required. IF damaged, replace (

pg. 20

). IF NOT

damaged, contact tech support (908) 355-7995.

Inspect orifices & burner tubes

Step 12H

Step 12F

12. Service LED ON: “IF” Code (cont.)

Содержание H150FDN

































































Результаты поиска

Содержание H150FDN

Отзывы:

Похожие инструкции для H150FDN

Бренды по названию

Популярные бренды

Hayward H150FDN, Руководство по устранению неисправностей

Результаты поиска

Содержание H150FDN

Отзывы:

Похожие инструкции для H150FDN

Бренды по названию

Популярные бренды