manualshive.com logo in svg

Hayward H150FDN, Руководство по устранению неисправностей

Приобретите Hayward H150FDN в нашем магазине и получите бесплатное руководство по устранению неполадок. Скачайте его с нашего сайте, чтобы быть в курсе всех подробностей работы продукта. Руководство доступно для загрузки на manualshive.com. Не упустите возможность ознакомиться с инструкцией перед использованием продукта.

Поделиться
Скачать
background image

“SF” OR  

“HS” Code 

Check display for 

“

SF

” code 

Is “SF” code 

present? 

The “

HS

” code 

stands for High 

Sense (water 

temperature). 

YES 

NO 

Ohm thermistor, 

checking each red to 

black, do the readings 

differ by more than 1°? 

40 

Replace 

thermistor: 

FDXLTER1930 

YES 

NO 

8. Service LED ON: “SF” OR “HS” Code 

Replace ICB: 

FDXLICB1930 

Make sure water 

inlet & outlet are 

plumbed correctly, 

are they reversed? 

YES 

Plumb correctly in 

compliance with 

installation manual 

NO 

Ohm thermistor, 

checking each red to 

black, do the readings 

differ by more than 1°? 

NO 

Replace ICB: 

FDXLICB1930 

Replace 

thermistor: 

FDXLTER1930 

YES 

Содержание H150FDN


































































Отзывы:

Нет отзывов

Похожие инструкции для H150FDN

A.O. Smith 100 Series Installation And Operating Manual preview
100 Series
Бренд: A.O. Smith Страницы: 56
Garden Treasures Living PG171H-B Manual preview
PG171H-B
Бренд: Garden Treasures Living Страницы: 18
MAINE ENERGY SYSTEMS PELLEMATIC SmartXS Operating Manual preview
PELLEMATIC SmartXS
Бренд: MAINE ENERGY SYSTEMS Страницы: 82
Rheem Pronto 012 Owner'S Manual And Installation Instructions preview
Pronto 012
Бренд: Rheem Страницы: 28
Atlantic Ingenio VM 050 D400-3-E Instruction Manual preview
Ingenio VM 050 D400-3-E
Бренд: Atlantic Страницы: 69
Beper RI.064 Use Instructions preview
RI.064
Бренд: Beper Страницы: 92
A.O. Smith GPVX 75L Series Installation And Operating Manual preview
GPVX 75L Series
Бренд: A.O. Smith Страницы: 52
Parmet GP-300 Installation And Service Manual preview
GP-300
Бренд: Parmet Страницы: 6
A.O. Smith BTH 120-250(A) Installation & Operating Instructions Manual preview
BTH 120-250(A)
Бренд: A.O. Smith Страницы: 32
CEL-FI cellmate Quick Start Manual preview
cellmate
Бренд: CEL-FI Страницы: 2
Salda Comfort Box Technical Manual preview
Comfort Box
Бренд: Salda Страницы: 14
Olimpia splendid Caldo Relax Instructions For Use And Maintenance Manual preview
Caldo Relax
Бренд: Olimpia splendid Страницы: 212
Resolution Products Repeater Translator RE220T Quick Start Manual preview
Repeater Translator RE220T
Бренд: Resolution Products Страницы: 2
Tulikivi TUISKU XL Installation Manual preview
TUISKU XL
Бренд: Tulikivi Страницы: 36
Nippa WB18 Installation And Operating Manual preview
WB18
Бренд: Nippa Страницы: 12
Parasol SunPhase 25E LP Installation And Operating Instructions Manual preview
SunPhase 25E LP
Бренд: Parasol Страницы: 11
Trumatic S 3000 P Operating Instructions Manual preview
S 3000 P
Бренд: Trumatic Страницы: 9
Saivod MICA MH-02 Manual preview
MICA MH-02
Бренд: Saivod Страницы: 22

Бренды по названию

Популярные бренды

Загрузить еще бренды