manualshive.com logo in svg

Hayward EcoStar SP3400VSP, Руководство пользователя

Поделиться
Скачать
Hayward EcoStar SP3400VSP Скачать руководство пользователя страница 22

 

 

 

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS 

Page 22 of 32 

EcoStar Variable Speed Pump 

IS3400VSP Rev-B 

3.  

 

 

 

 

 

 

 

 

Note:  For SP3400VSPVR only, the SVRS feature is disabled during Quick Clean mode.  When Quick Clean is pressed, 
the above message is displayed to alert the user that SVRS is disabled, and that all bathers should exit the pool 
during Quick Clean.  If bathers are in the water, pr will return the pump to normal operation.  If bathers are 
not in the water, pressing – will allow the pump to run in Quick Clean mode, where it will run at the Max Allowed 
Speed set in the Configuration Menu for 60 minutes.  When Quick Clean is selected for SP3400VSP, the pump will 
immediately proceed to Quick Clean mode. 

4.  

 

 

 

 

 

 

 

5.  

 

 

 

 

 

 

 

6.  

 

 

 

 

 

 

 

 

Note:  The above message will be displayed while Quick Clean is running.  For SP3400VSPVR, the check system light 
will also flash on and off every two seconds as an additional reminder that SVRS is inactive.  Quick Clean mode 
expires after 60 min, and it may be cancelled early by pressing the Stop/Resume button, at which time the pump 
would return to normal operation.  For SP3400VSP, the SVRS Inactive message will not be shown, and the Check 
System LED will not flash. 

5.12. Remote Stop 

 

Screen 

 

 

1.  

 

 

 

 

 

 

 

 

Note:  The above message will be displayed when an installed remote stop switch is activated.  The pump will 
remain stopped until the remote stop switch is deactivated. 

6. Maintenance 

• 

Clean strainer basket regularly.  Do NOT strike basket to clean.  Inspect strainer cover gasket regularly and replace as 

necessary. 

• 

Hayward pumps have self-lubricating motor bearings and shaft seals.  No lubrication is necessary. 

• 

Keep motor clean.  Insure motor air vents are free from obstruction to avoid damage.  Do NOT use water to hose off 

motor. 

• 

Occasionally, shaft seals must be replaced, due to wear or damage.  Replace with genuine Hayward seal assembly 

kit.  See “Shaft Seal Change Instructions” in this manual. 

7. Storage 

/ 

Winterization 

 

WARNING 

– Separation Hazard.  Do not purge the system with compressed air.  Purging the system with 

compressed air can cause components to explode, with risk of severe injury or death to anyone nearby.  Use only a 
low pressure (below 5 PSI), high volume blower when air purging the pump, filter, or piping. 

Bathers in water? 

+ = yes; - = no

 

SVRS Inactive 

Quick Clean running

 

SVRS Inactive 

Press resume to end.

 

SVRS Inactive 

3200 rpm for 60 min;

 

Remote Stop 

is engaged

 

Содержание EcoStar SP3400VSP

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды