background image

6. Care and maintenance

Cleaning

• Careful cleaning of the tool, in particular, the moving parts contributes towards a longer

useful life. Remember that dust, sand, environmental influences, in particular a high salt
index, and dirt in general are extremely damaging to hydraulic tools.

• Particular care should be taken when cleaning the pump drive piston and the piston.

The tiniest of contaminations may scratch the walls of the cylinder and damage the
leak-proof seals. For the correct cleaning of the piston, we recommend extending the
piston and then cleaning it with a high-quality, non-corrosive solution.

Power switch

Check to see whether the switch on the machine automatically pops out again when you
release it.

Storage

To prevent damage to the tool as a result of bumps, dust etc. you should if possible store the
tools in the original packaging.

Guarantee:

2 year guarantee when used for the purpose it is intended when the annual maintenance inter-
vals are maintained by an authorised HAUPA service centre. We reserve the right to rework the
product.

Faults:

Loss of oil: 
Send to the HAUPA service centre. Do not open!

Disposal:

…in accordance with the scope of validity of the European WEEE (2002/96/EU) and RoHS
directives (2002/95/EU). Batteries must be disposed off separating according to the battery
directive.

WITH EVERY REPLACEMENT PART ORDER, INCLUDE THE FOLLOWING INFORMATION:
1) Article number.
2) Article description.
3) Reference to the operating instructions and/or date.
4) Tool type.
5) Serial number of the tool.

The guarantee is voided if you use parts that are not original replacement parts from HAUPA.

Содержание AS-52ACSR









Отзывы: